JAJSL52A april   2020  – february 2021 BQ25968

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 概要 (続き)
  7. 6 Device Comparison Table
  8. 7 Pin Configuration and Functions
  9. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Charging System
      2. 9.3.2  Battery Charging Profile
      3. 9.3.3  Control State Diagram for System Implementation
      4. 9.3.4  Device Power Up
      5. 9.3.5  Switched Cap Function
        1. 9.3.5.1 Theory of Operation
      6. 9.3.6  Charging Start-Up
      7. 9.3.7  Integrated 16-Bit ADC for Monitoring and Smart Adapter Feedback
      8. 9.3.8  Device Internal Thermal Shutdown, TSBUS, and TSBAT Temperature Monitoring
      9. 9.3.9  INT Pin, STAT, FLAG, and MASK Registers
      10. 9.3.10 CDRVH and CDRVL_ADDRMS Functions
      11. 9.3.11 Parallel Operation Using Master and Slave Modes
    4. 9.4 Device Functional Modes
      1. 9.4.1 Device Modes and Protection Status
        1. 9.4.1.1 Input Overvoltage, Overcurrent, Undercurrent and Short-Circuit Protection
        2. 9.4.1.2 Battery Overvoltage and Overcurrent Protection
        3. 9.4.1.3 Cycle-by-Cycle Current Limit
    5. 9.5 Programming
      1. 9.5.1 F/S Mode Protocol
    6. 9.6 Register Maps
      1. 9.6.1 Customer Registers
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Standalone Application Information (for use with switching charger)
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
        3. 10.2.1.3 Application Curves
      2. 10.2.2 Parallel BQ25968 for Higher Power Applications
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
        3. 10.2.2.3 Application Curve
  12. 11Power Supply Recommendations
  13. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  14. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 サード・パーティ製品に関する免責事項
      2. 13.1.2 Device Nomenclature
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 ドキュメントの更新通知を受け取る方法
    4. 13.4 サポート・リソース
    5. 13.5 Trademarks
    6. 13.6 静電気放電に関する注意事項
    7. 13.7 用語集
  15. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

10.1 Application Information

A typical application consists of the device configured as an I2C controlled parallel charger along with a standard switching charger, however, it can also be used with a linear charger or PMIC with integrated charger as well. For simplicity, it is called the primary charger. As shown in Figure 9-2 the device can start fast charging after the primary charger completes precharging, where the BQ25890 is used as the primary charger. The device will then hand back charging to the primary charger when final current tapering is desired. This point is usually where the efficiency of the primary charger is acceptable for the application. The device can be used to charge Li-ion and Li-polymer batteries used in a wide range of smartphones and other portable devices. To take advantage of the high charge current capabilities of the BQ25968, it may be necessary to charge in excess of 1C. In this case, be sure to follow the battery manufacturers recommendations closely.