JAJSTU7H August   2007  – July 2024 CDCE937 , CDCEL937

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements: CLK_IN
    7. 5.7 Timing Requirements: SDA/SCL
    8. 5.8 EEPROM Specification
    9. 5.9 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Control Terminal Setting
      2. 7.3.2 Default Device Setting
      3. 7.3.3 SDA/SCL Serial Interface
      4. 7.3.4 Data Protocol
    4. 7.4 Device Functional Modes
      1. 7.4.1 SDA/SCL Hardware Interface
    5. 7.5 Programming
  9. 8 Register Maps
    1. 8.1 SDA/SCL Configuration Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Spread Spectrum Clock (SSC)
        2. 9.2.2.2 PLL Frequency Planning
        3. 9.2.2.3 Crystal Oscillator Start-Up
        4. 9.2.2.4 Frequency Adjustment With Crystal Oscillator Pulling
        5. 9.2.2.5 Unused Inputs and Outputs
        6. 9.2.2.6 Switching Between XO and VCXO Mode
      3. 9.2.3 Application Curves
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 サード・パーティ製品に関する免責事項
      2. 12.1.2 Development Support
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 ドキュメントの更新通知を受け取る方法
    4. 12.4 サポート・リソース
    5. 12.5 Trademarks
    6. 12.6 静電気放電に関する注意事項
    7. 12.7 用語集
  14. 13Revision History
  15. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.3.1 Control Terminal Setting

The CDCEx937 has three user-definable control terminals (S0, S1, and S2) which allow external control of device settings. The terminals can be programmed to any of the following setting:

  • Spread spectrum clocking selection → spread type and spread amount selection
  • Frequency selection → switching between any of two user-defined frequencies
  • Output state selection → output configuration and power down control

The user can predefine up to eight different control settings. Table 7-1 and Table 7-2 explain these settings.

Table 7-1 Control Terminal Definition
EXTERNAL
CONTROL BITS		PLL1 SETTINGPLL2 SETTINGPLL3 SETTINGY1 SETTING
Control FunctionPLL
Frequency
Selection		SSC SelectionOutput Y2/Y3
Selection		PLL
Frequency
Selection		SSC SelectionOutput Y4/Y5
Selection		PLL
Frequency
Selection		SSC
Selection		Output Y6/Y7
Selection		Output Y1
and Power-Down
Selection
Table 7-2 PLLx Setting (Can Be Selected for Each PLL Individual)
SSC SELECTION (CENTER/DOWN)(1)
SSCx [3-bits]CENTERDOWN
0000% (off)0% (off)
001±0.25%–0.25%
010±0.5%–0.5%
011±0.75%–0.75%
100±1%–1%
101±1.25%–1.25%
110±1.5%–1.5%
111±2%–2%
FREQUENCY SELECTION(2)
FSxFUNCTION
0Frequency0
1Frequency1
OUTPUT SELECTION(3) (Y2 ... Y7)
YxYxFUNCTION
0State0
1State1
(1) Center/Down-Spread, Frequency0/1 and State0/1 are user-definable in PLLx Configuration Register
(2) Frequency0 and Frequency1 can be any frequency within the specified fVCO range
(3) State0/1 selection is valid for both outputs of the corresponding PLL module and can be power down, 3-state, low or active
Table 7-3 Y1 Setting(1)
Y1 SELECTION
Y1FUNCTION
0State 0
1State 1
(1) State0 and State1 are user definable in Generic Configuration Register and can be power down, 3-state, low, or active.

S1/SDA and S2/SCL pins of the CDCEx937 are dual function pins. In default configuration the pins are defined as SDA/SCL for the serial interface. The pins can be programmed as control-pins (S1/S2) by setting the relevant bits in the EEPROM. Note that the changes to the Control register (Bit [6] of Byte [02]) have no effect until the pins are written into the EEPROM.

Once the pins are set as control pins, the serial programming interface is no longer available. However, if VDDOUT is forced to GND, the two control-pins, S1 and S2, temporally act as serial programming pins (SDA/SCL).

S0 is not a multi-use pin, the pin is a control pin only.