JAJSLP1 September   2023 DAC43901-Q1 , DAC43902-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics: Comparator Mode
    6. 6.6  Electrical Characteristics: General
    7. 6.7  Timing Requirements: I2C Standard Mode
    8. 6.8  Timing Requirements: I2C Fast Mode
    9. 6.9  Timing Requirements: I2C Fast-Mode Plus
    10. 6.10 Timing Requirements: SPI Write Operation
    11. 6.11 Timing Requirements: SPI Read and Daisy Chain Operation (FSDO = 0)
    12. 6.12 Timing Requirements: SPI Read and Daisy Chain Operation (FSDO = 1)
    13. 6.13 Timing Requirements: PWM Output
    14. 6.14 Timing Diagrams
    15. 6.15 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Smart Digital-to-Analog Converter (DAC) Architecture
      2. 7.3.2 Threshold DAC
        1. 7.3.2.1 Voltage Reference and DAC Transfer Function
        2. 7.3.2.2 Power-Supply as Reference
        3. 7.3.2.3 Internal Reference
        4. 7.3.2.4 External Reference
      3. 7.3.3 Programming Interface
      4. 7.3.4 Nonvolatile Memory (NVM)
        1. 7.3.4.1 NVM Cyclic Redundancy Check (CRC)
          1. 7.3.4.1.1 NVM-CRC-FAIL-USER Bit
          2. 7.3.4.1.2 NVM-CRC-FAIL-INT Bit
      5. 7.3.5 Power-On Reset (POR)
      6. 7.3.6 External Reset
      7. 7.3.7 Register-Map Lock
    4. 7.4 Device Functional Modes
      1. 7.4.1 Comparator Mode
      2. 7.4.2 PWM Fade-In Fade-Out Mode
      3. 7.4.3 Sequential Turn-Indicator Animation Mode
    5. 7.5 Programming
      1. 7.5.1 SPI Programming Mode
      2. 7.5.2 I2C Programming Mode
        1. 7.5.2.1 F/S Mode Protocol
        2. 7.5.2.2 I2C Update Sequence
          1. 7.5.2.2.1 Address Byte
          2. 7.5.2.2.2 Command Byte
        3. 7.5.2.3 I2C Read Sequence
    6. 7.6 Register Maps
      1. 7.6.1  NOP Register (address = 00h) [reset = 0000h]
      2. 7.6.2  DAC-x-VOUT-CMP-CONFIG Register (address = 15h, 03h)
      3. 7.6.3  COMMON-CONFIG Register (address = 1Fh)
      4. 7.6.4  COMMON-TRIGGER Register (address = 20h) [reset = 0000h]
      5. 7.6.5  COMMON-PWM-TRIG Register (address = 21h) [reset = 0000h]
      6. 7.6.6  GENERAL-STATUS Register (address = 22h) [reset = 00h, DEVICE-ID, VERSION-ID]
      7. 7.6.7  INTERFACE-CONFIG Register (address = 26h) [reset = 0000h]
      8. 7.6.8  STATE-MACHINE-CONFIG0 Register (address = 27h) [reset = 0003h]
      9. 7.6.9  SRAM-CONFIG Register (address = 2Bh) [reset = 0000h]
      10. 7.6.10 SRAM-DATA Register (address = 2Ch) [reset = 0000h]
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Sequential Turn Indicator
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curve
      2. 8.2.2 Logarithmic Fade-In Fade-Out
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 ドキュメントの更新通知を受け取る方法
    2. 9.2 サポート・リソース
    3. 9.3 Trademarks
    4. 9.4 静電気放電に関する注意事項
    5. 9.5 用語集
  11. 10Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.2.1.2 Detailed Design Procedure

The TL431LI-Q1 adjustable precision shunt regulator can be used to supply the DAC43902-Q1 from the 12-V system voltage. The TL431LI-Q1 has a 2.5-V precision reference. Two 10-kΩ resistors are used as shown in the simplified figure to regulate the output voltage to 5 V to supply DAC43902-Q1.

In some tail-light designs, the LED driver is supplied by a PWM signal to control the flashing of the LEDs. If this is the case, the trigger input of the DAC43902-Q1 can be tied to VDD. The sequential turn animation begins automatically when VDD is applied.

The state machine in the DAC43902-Q1 is enabled by default; therefore, the PWM outputs are used with the default settings when the VREF/MODE pin is pulled high. To change these default parameters, pull the VREF/MODE pin low to enter programming mode, and write a 0 to the SM-START and SM-EN bits of the STATE-MACHINE-CONFIG0 register to disable the state machine. After the state machine is disabled, program the SRAM parameters and register settings to configure the DAC43902-Q1:

On the rising edge of TRIG-IN, the DAC43902-Q1 PWM outputs fade-in to the 7-bit PWM duty cycle defined in the PWM-MAX parameter located in bits [6:0] of SRAM location 0x21. On the falling edge of TRIG-IN, the PWM outputs jump to the 7-bit PWM duty cycle defined in the PWM-MIN parameter located in bits [6:0] of SRAM location 0x20.

The 5-bit PWM frequency is set in the PWM-FREQ parameter located in bits [11:7] of SRAM location 0x22. The available PWM frequencies are given in Table 7-7. The TPS92633-Q1 LED driver used in the example schematic recommends a 200-Hz PWM frequency with a 1% to 100% duty cycle for brightness control. In that case, the maximum frequency setting of 31 can be set in PWM-FREQ to get a PWM output frequency of 218 Hz. Make sure to left shift this value by 7 bits when loading the parameter into the SRAM location.

The four PWM output channels use the same fade-in rate as defined in the FADE-IN SLEW-RATE parameter located in bits [15:0] of SRAM location 0x23. The total fade-in time can be calculated using Equation 4 and Equation 5. The SLEW-RATE parameter is used in Equation 4 to get the tSLEW_RATE in ms/step. For example, if a value of 235 is used for the FADE-IN SLEW-RATE parameter, the resulting tSLEW-RATE is: 0.569 ms/step.

The information given in Table 7-5 is used to calculate the total number of duty cycle steps in the fade-in. If PWM-MIN is set to 0 and PWM-MAX is set to 0x7F, a total of 176 steps are needed. Equation 5 calculates the total fade time, tFADE as 100.2 ms.

The delays between each channel are configured in the CH0-DELAY and COM-DELAY parameters in bits [15:0] of SRAM location 0x24 and 0x25, respectively. CH0-DELAY represents the delay between the rising edge of trigger and the start of channel 0. COM-DELAY represents the delay between the start of channel 0 and the start of channel 1, the start of channel 1 and the start of channel 2, and the start of channel 2 and the start of channel 3. The delay time is calculated using Equation 7. If a delay value of 176 is set in the COM-DELAY parameter, the delay is 100.2 ms.

After all register settings and SRAM parameters are configured, restart the state machine by writing a 1 to the SM-START and SM-EN bits of the STATE-MACHINE-CONFIG0 register. Save these settings to the NVM by writing a 1 to the NVM-PROG bit of the COMMON-TRIGGER register. Pull the VREF/MODE pin high to put the device in standalone mode and enable the PWM outputs on the digital interface pins.

The SRAM parameters and register settings need to be applied to the second DAC43902-Q1 or DAC43901-Q1 in the cascade as well. Apply the TRIG-OUT on channel 1 of the first DAC43902-Q1, to the trigger input on TRIG-IN of the second device.

The pseudocode for getting started with a sequential turn indicator application is as follows:

//SYNTAX: WRITE <REGISTER NAME (REGISTER ADDRESS)>, <MSB DATA>, <LSB DATA>
//Pull VREF/MODE pin low to enter programming mode
//Disable the state machine
WRITE STATE-MACHINE-CONFIG0(0x27), 0x00, 0x00
//Power-up DAC channels 0 and 1, disable the internal reference
WRITE COMMON-CONFIG(0x1F), 0x03, 0xF9
//Enable comparator settings for channel 0, and set reference to VDD
WRITE DAC-0-VOUT-CMP-CONFIG(0x15), 0x04, 0x07
//Set the reference for channel 1 to VDD
WRITE DAC-1-VOUT-CMP-CONFIG(0x3), 0x04, 0x00
//Set the comparator threshold to mid-scale
WRITE SRAM-ADDR(0x2B), 0x00, 0x27
WRITE SRAM-DATA(0x2C), 0x80, 0x00
//Set max PWM duty cycle to 100%
WRITE SRAM-ADDR(0x2B), 0x00, 0x21
WRITE SRAM-DATA(0x2C), 0x00, 0x7F
//Set min PWM duty cycle to 0%
WRITE SRAM-ADDR(0x2B), 0x00, 0x20
WRITE SRAM-DATA(0x2C), 0x00, 0x00
//Set PWM frequency to 218Hz
WRITE SRAM-ADDR(0x2B), 0x00, 0x22
WRITE SRAM-DATA(0x2C), 0x0F, 0x80
//Set fade-in time to 100.2 ms
WRITE SRAM-ADDR(0x2B), 0x00, 0x23
WRITE SRAM-DATA(0x2C), 0x00, 0xEB
//Set the CH0 delay to 0
WRITE SRAM-ADDR(0x2B), 0x00, 0x24
WRITE SRAM-DATA(0x2C), 0x00, 0x00
//Set the COM delay to 100.2 ms
WRITE SRAM-ADDR(0x2B), 0x00, 0x25
WRITE SRAM-DATA(0x2C), 0x00, 0xB0
//Enable and start the state machine
WRITE STATE-MACHINE-CONFIG0(0x27), 0x00, 0x03
//Save all settings in NVM
WRITE COMMON-TRIGGER(0x20) 0x00, 0x02
//Pull the VREF/MODE pin high to enter standalone mode