JAJSMH2A July   2021  – August 2021 DLPC1438

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Power Electrical Characteristics
    6. 6.6  Pin Electrical Characteristics
    7. 6.7  Internal Pullup and Pulldown Electrical Characteristics
    8. 6.8  DMD Sub-LVDS Interface Electrical Characteristics
    9. 6.9  DMD Low-Speed Interface Electrical Characteristics
    10. 6.10 System Oscillator Timing Requirements
    11. 6.11 Power Supply and Reset Timing Requirements
    12. 6.12 Parallel Interface Frame Timing Requirements
    13. 6.13 Parallel Interface General Timing Requirements
    14. 6.14 BT656 Interface General Timing Requirements
    15. 6.15 Flash Interface Timing Requirements
    16. 6.16 Other Timing Requirements
    17. 6.17 DMD Sub-LVDS Interface Switching Characteristics
    18. 6.18 DMD Parking Switching Characteristics
    19. 6.19 Chipset Component Usage Specification
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Input Source
        1. 7.3.1.1 Supported Resolution and Frame Rates
        2. 7.3.1.2 Parallel Interface
      2. 7.3.2 External Print
      3. 7.3.3 Device Startup
      4. 7.3.4 SPI Flash
        1. 7.3.4.1 SPI Flash Interface
        2. 7.3.4.2 SPI Flash Programming
      5. 7.3.5 I2C Interface
      6. 7.3.6 Test Point Support
      7. 7.3.7 DMD Interface
        1. 7.3.7.1 Sub-LVDS (HS) Interface
    4. 7.4 Device Functional Modes
    5. 7.5 Programming
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Pattern projector for 3D printer without actuation and without FPGA
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curve
      2. 8.2.2 Pattern projector for 3D printer with actuator
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
        3. 8.2.2.3 Application Curve
  9. 9 Power Supply Recommendations
    1. 9.1 PLL Design Considerations
    2. 9.2 System Power-Up and Power-Down Sequence
    3. 9.3 Power-Up Initialization Sequence
    4. 9.4 DMD Fast Park Control (PARKZ)
    5. 9.5 Hot Plug I/O Usage
  10. 10Layout
    1. 10.1 Layout Guidelines
      1. 10.1.1 PLL Power Layout
      2. 10.1.2 Reference Clock Layout
        1. 10.1.2.1 Recommended Crystal Oscillator Configuration
      3. 10.1.3 Unused Pins
      4. 10.1.4 DMD Control and Sub-LVDS Signals
      5. 10.1.5 Layer Changes
      6. 10.1.6 Stubs
      7. 10.1.7 Terminations
      8. 10.1.8 Routing Vias
      9. 10.1.9 Thermal Considerations
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
      2. 11.1.2 Device Nomenclature
        1. 11.1.2.1 Device Markings
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 サポート・リソース
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

10.1.4 DMD Control and Sub-LVDS Signals

Table 10-4 Maximum Pin-to-Pin PCB Interconnect Recommendations
DMD BUS SIGNAL(1)(2)SIGNAL INTERCONNECT TOPOLOGYUNIT
SINGLE-BOARD SIGNAL ROUTING LENGTHMULTI-BOARD SIGNAL ROUTING LENGTH
DMD_HS_CLK_P
DMD_HS_CLK_N		6.0
(152.4)		See (3)in
(mm)
DMD_HS_WDATA_A_P
DMD_HS_WDATA_A_N		6.0
(152.4)		See (3)in
(mm)
DMD_HS_WDATA_B_P
DMD_HS_WDATA_B_N
DMD_HS_WDATA_C_P
DMD_HS_WDATA_C_N
DMD_HS_WDATA_D_P
DMD_HS_WDATA_D_N
DMD_HS_WDATA_E_P
DMD_HS_WDATA_E_N
DMD_HS_WDATA_F_P
DMD_HS_WDATA_F_N
DMD_HS_WDATA_G_P
DMD_HS_WDATA_G_N
DMD_HS_WDATA_H_P
DMD_HS_WDATA_H_N
DMD_LS_CLK6.5
(165.1)		See (3)in
(mm)
DMD_LS_WDATA6.5
(165.1)		See (3)in
(mm)
DMD_LS_RDATA6.5
(165.1)		See (3)in
(mm)
DMD_DEN_ARSTZ7.0
(177.8)		See (3)in
(mm)
(1) Maximum signal routing length includes escape routing.
(2) Multi-board DMD routing length is more restricted due to the impact of the connector.
(3) Due to PCB variations, these recommendations cannot be defined. Any board design should SPICE simulate with the controller IBIS model (found under the Tools & Software tab of the controller web page) to ensure routing lengths do not violate signal requirements.
Table 10-5 High Speed PCB Signal Routing Matching Requirements
SIGNAL GROUP LENGTH MATCHING(1)(2)(3)
INTERFACESIGNAL GROUPREFERENCE SIGNALMAX MISMATCH(4)UNIT
DMD(5)DMD_HS_WDATA_A_P
DMD_HS_WDATA_A_N		DMD_HS_CLK_P
DMD_HS_CLK_N		±1.0
(±25.4)		in
(mm)
DMD_HS_WDATA_B_P
DMD_HS_WDATA_B_N
DMD_HS_WDATA_C_P
DMD_HS_WDATA_C_N
DMD_HS_WDATA_D_P
DMD_HS_WDATA_D_N
DMD_HS_WDATA_E_P
DMD_HS_WDATA_E_N
DMD_HS_WDATA_F_P
DMD_HS_WDATA_F_N
DMD_HS_WDATA_G_P
DMD_HS_WDATA_G_N
DMD_HS_WDATA_H_P
DMD_HS_WDATA_H_N
DMDDMD_HS_WDATA_x_PDMD_HS_WDATA_x_N±0.025
(±0.635)		in
(mm)
DMDDMD_HS_CLK_PDMD_HS_CLK_N±0.025
(±0.635)		in
(mm)
DMDDMD_LS_WDATA
DMD_LS_RDATA		DMD_LS_CLK±0.2
(±5.08)		in
(mm)
DMDDMD_DEN_ARSTZN/AN/Ain
(mm)
(1) The length matching values apply to PCB routing lengths only. Internal package routing mismatch associated with the DLPC1438 controller or the DMD require no additional consideration.
(2) Training is applied to DMD HS data lines. This is why the defined matching requirements are slightly relaxed compared to the LS data lines.
(3) DMD LS signals are single ended.
(4) Mismatch variance for a signal group is always with respect to the reference signal.
(5) DMD HS data lines are differential, thus these specifications are pair-to-pair.
Table 10-6 Signal Requirements
PARAMETERREFERENCEREQUIREMENT
Source series terminationDMD_LS_WDATARequired
DMD_LS_CLKRequired
DMD_DEN_ARSTZAcceptable
DMD_LS_RDATARequired
DMD_HS_WDATA_x_yNot acceptable
DMD_HS_CLK_yNot acceptable
Endpoint terminationDMD_LS_WDATANot acceptable
DMD_LS_CLKNot acceptable
DMD_DEN_ARSTZNot acceptable
DMD_LS_RDATANot acceptable
DMD_HS_WDATA_x_yNot acceptable
DMD_HS_CLK_yNot acceptable
PCB impedanceDMD_LS_WDATA68 Ω ±10%
DMD_LS_CLK68 Ω ±10%
DMD_DEN_ARSTZ68 Ω ±10%
DMD_LS_RDATA68 Ω ±10%
DMD_HS_WDATA_x_y100 Ω ±10%
DMD_HS_CLK_y100 Ω ±10%
Signal typeDMD_LS_WDATASDR (single data rate) referenced to DMD_LS_DCLK
DMD_LS_CLKSDR referenced to DMD_LS_DCLK
DMD_DEN_ARSTZSDR
DMD_LS_RDATASDR referenced to DMD_LS_DLCK
DMD_HS_WDATA_x_ysub-LVDS
DMD_HS_CLK_ysub-LVDS