JAJSFY1A August   2018  – June  2019 DRV8350 , DRV8350R , DRV8353 , DRV8353R

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     概略回路図
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
    1.     Pin Functions—32-Pin DRV8350 Devices
    2.     Pin Functions—48-Pin DRV8350R Devices
    3.     Pin Functions—40-Pin DRV8353 Devices
    4.     Pin Functions—48-Pin DRV8353R Devices
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 SPI Timing Requirements
    7. 8.7 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Three Phase Smart Gate Drivers
        1. 9.3.1.1 PWM Control Modes
          1. 9.3.1.1.1 6x PWM Mode (PWM_MODE = 00b or MODE Pin Tied to AGND)
          2. 9.3.1.1.2 3x PWM Mode (PWM_MODE = 01b or MODE Pin = 47 kΩ to AGND)
          3. 9.3.1.1.3 1x PWM Mode (PWM_MODE = 10b or MODE Pin = Hi-Z)
          4. 9.3.1.1.4 Independent PWM Mode (PWM_MODE = 11b or MODE Pin Tied to DVDD)
        2. 9.3.1.2 Device Interface Modes
          1. 9.3.1.2.1 Serial Peripheral Interface (SPI)
          2. 9.3.1.2.2 Hardware Interface
        3. 9.3.1.3 Gate Driver Voltage Supplies and Input Supply Configurations
        4. 9.3.1.4 Smart Gate Drive Architecture
          1. 9.3.1.4.1 IDRIVE: MOSFET Slew-Rate Control
          2. 9.3.1.4.2 TDRIVE: MOSFET Gate Drive Control
          3. 9.3.1.4.3 Propagation Delay
          4. 9.3.1.4.4 MOSFET VDS Monitors
          5. 9.3.1.4.5 VDRAIN Sense and Reference Pin
      2. 9.3.2 DVDD Linear Voltage Regulator
      3. 9.3.3 Pin Diagrams
      4. 9.3.4 Low-Side Current-Shunt Amplifiers (DRV8353 and DRV8353R Only)
        1. 9.3.4.1 Bidirectional Current Sense Operation
        2. 9.3.4.2 Unidirectional Current Sense Operation (SPI only)
        3. 9.3.4.3 Amplifier Calibration Modes
        4. 9.3.4.4 MOSFET VDS Sense Mode (SPI Only)
      5. 9.3.5 Step-Down Buck Regulator
        1. 9.3.5.1 Functional Block Diagram
        2. 9.3.5.2 Feature Description
          1. 9.3.5.2.1 Control Circuit Overview
          2. 9.3.5.2.2 Start-Up Regulator (VCC)
          3. 9.3.5.2.3 Regulation Comparator
          4. 9.3.5.2.4 Overvoltage Comparator
          5. 9.3.5.2.5 On-Time Generator and Shutdown
          6. 9.3.5.2.6 Current Limit
          7. 9.3.5.2.7 N-Channel Buck Switch and Driver
          8. 9.3.5.2.8 Thermal Protection
      6. 9.3.6 Gate Driver Protective Circuits
        1. 9.3.6.1 VM Supply and VDRAIN Undervoltage Lockout (UVLO)
        2. 9.3.6.2 VCP Charge-Pump and VGLS Regulator Undervoltage Lockout (GDUV)
        3. 9.3.6.3 MOSFET VDS Overcurrent Protection (VDS_OCP)
          1. 9.3.6.3.1 VDS Latched Shutdown (OCP_MODE = 00b)
          2. 9.3.6.3.2 VDS Automatic Retry (OCP_MODE = 01b)
          3. 9.3.6.3.3 VDS Report Only (OCP_MODE = 10b)
          4. 9.3.6.3.4 VDS Disabled (OCP_MODE = 11b)
        4. 9.3.6.4 VSENSE Overcurrent Protection (SEN_OCP)
          1. 9.3.6.4.1 VSENSE Latched Shutdown (OCP_MODE = 00b)
          2. 9.3.6.4.2 VSENSE Automatic Retry (OCP_MODE = 01b)
          3. 9.3.6.4.3 VSENSE Report Only (OCP_MODE = 10b)
          4. 9.3.6.4.4 VSENSE Disabled (OCP_MODE = 11b or DIS_SEN = 1b)
        5. 9.3.6.5 Gate Driver Fault (GDF)
        6. 9.3.6.6 Overcurrent Soft Shutdown (OCP Soft)
        7. 9.3.6.7 Thermal Warning (OTW)
        8. 9.3.6.8 Thermal Shutdown (OTSD)
        9. 9.3.6.9 Fault Response Table
    4. 9.4 Device Functional Modes
      1. 9.4.1 Gate Driver Functional Modes
        1. 9.4.1.1 Sleep Mode
        2. 9.4.1.2 Operating Mode
        3. 9.4.1.3 Fault Reset (CLR_FLT or ENABLE Reset Pulse)
      2. 9.4.2 Buck Regulator Functional Modes
        1. 9.4.2.1 Shutdown Mode
        2. 9.4.2.2 Active Mode
    5. 9.5 Programming
      1. 9.5.1 SPI Communication
        1. 9.5.1.1 SPI
          1. 9.5.1.1.1 SPI Format
    6. 9.6 Register Maps
      1. 9.6.1 Status Registers
        1. 9.6.1.1 Fault Status Register 1 (address = 0x00h)
          1. Table 11. Fault Status Register 1 Field Descriptions
        2. 9.6.1.2 Fault Status Register 2 (address = 0x01h)
          1. Table 12. Fault Status Register 2 Field Descriptions
      2. 9.6.2 Control Registers
        1. 9.6.2.1 Driver Control Register (address = 0x02h)
          1. Table 14. Driver Control Field Descriptions
        2. 9.6.2.2 Gate Drive HS Register (address = 0x03h)
          1. Table 15. Gate Drive HS Field Descriptions
        3. 9.6.2.3 Gate Drive LS Register (address = 0x04h)
          1. Table 16. Gate Drive LS Register Field Descriptions
        4. 9.6.2.4 OCP Control Register (address = 0x05h)
          1. Table 17. OCP Control Field Descriptions
        5. 9.6.2.5 CSA Control Register (DRV8353 and DRV8353R Only) (address = 0x06h)
          1. Table 18. CSA Control Field Descriptions
        6. 9.6.2.6 Driver Configuration Register (DRV8353 and DRV8353R Only) (address = 0x07h)
          1. Table 19. Driver Configuration Field Descriptions
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Primary Application
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
          1. 10.2.1.2.1 External MOSFET Support
            1. 10.2.1.2.1.1 MOSFET Example
          2. 10.2.1.2.2 IDRIVE Configuration
            1. 10.2.1.2.2.1 IDRIVE Example
          3. 10.2.1.2.3 VDS Overcurrent Monitor Configuration
            1. 10.2.1.2.3.1 VDS Overcurrent Example
          4. 10.2.1.2.4 Sense-Amplifier Bidirectional Configuration (DRV8353 and DRV8353R)
            1. 10.2.1.2.4.1 Sense-Amplifier Example
          5. 10.2.1.2.5 Single Supply Power Dissipation
          6. 10.2.1.2.6 Single Supply Power Dissipation Example
          7. 10.2.1.2.7 Buck Regulator Configuration (DRV8350R and DRV8353R)
        3. 10.2.1.3 Application Curves
      2. 10.2.2 Alternative Application
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
          1. 10.2.2.2.1 Sense Amplifier Unidirectional Configuration
            1. 10.2.2.2.1.1 Sense-Amplifier Example
            2. 10.2.2.2.1.2 Dual Supply Power Dissipation
            3. 10.2.2.2.1.3 Dual Supply Power Dissipation Example
  11. 11Power Supply Recommendations
    1. 11.1 Bulk Capacitance Sizing
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Buck-Regulator Layout Guidelines
    2. 12.2 Layout Example
  13. 13デバイスおよびドキュメントのサポート
    1. 13.1 デバイス・サポート
      1. 13.1.1 デバイスの項目表記
    2. 13.2 ドキュメントのサポート
      1. 13.2.1 関連資料
    3. 13.3 関連リンク
    4. 13.4 ドキュメントの更新通知を受け取る方法
    5. 13.5 コミュニティ・リソース
    6. 13.6 商標
    7. 13.7 静電気放電に関する注意事項
    8. 13.8 Glossary
  14. 14メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

10.2.1.2 Detailed Design Procedure

Table 21 lists the recommended values of the external components for the gate driver. Table 22 lists the recommended values of the external components for the buck regulator.

Table 21. DRV835x Gate-Driver External Components

COMPONENTS PIN 1 PIN 2 RECOMMENDED
CVM1 VM GND X5R or X7R, 0.1-µF, VM-rated capacitor
CVM2 VM GND ≥ 10 µF, VM-rated capacitor
CVCP VCP VM X5R or X7R, 1-µF, 16-V capacitor
CVGLS VGLS GND X5R or X7R, 1-µF, 16-V capacitor
CSW CPH CPL X5R or X7R, 47-nF, VDRAIN-rated capacitor
CDVDD DVDD DGND X5R or X7R, 1-µF, 6.3-V capacitor
RnFAULT VCC(1) nFAULT Pullup resistor
RSDO VCC(1) SDO Pullup resistor
RIDRIVE IDRIVE GND or DVDD DRV835x hardware interface
RVDS VDS GND or DVDD DRV835x hardware interface
RMODE MODE GND or DVDD DRV835x hardware interface
RGAIN GAIN GND or DVDD DRV835x hardware interface
CVREF VREF GND or DGND Optional capacitor rated for VREF
RASENSE SPA SNA and GND Sense shunt resistor
RBSENSE SPB SNB and GND Sense shunt resistor
RCSENSE SPC SNC and GND Sense shunt resistor
(1) VCC is not a pin on the DRV835x family of devices, but a VCC supply voltage pullup is required for the open-drain output nFAULT and SDO. These pins can also be pulled up to DVDD.

Table 22. DRV835xR Buck Regulator External Components

COMPONENT PIN 1 PIN 2 RECOMMENDED
CIN (2) VIN GND X5R or X7R, VIN-rated capacitor
CBST(2) BST SW X5R or X7R, 0.01-µF, 16-V rated capacitor
CVCC(2) VCC GND X5R or X7R, 0.47-µF, 16-V rated capacitor
DSW(2) SW GND Schottky diode
LSW(2) SW OUT(1) Output filter inductor
COUT (2) OUT(1) GND X5R or X7R, OUT-rated capacitor
ROUT(2) OUT(1) GND Output ripple resistor
RFB1(2) OUT(1) FB Resistor divider to set buck output voltage
RFB2(2) FB GND
(1) OUT is not a pin on the DRV8350R and DRV8353R devices, but the regulated output voltage of the buck regulator after the output inductor.
(2) For detailed design procedures, refer to the LM5008A 100-V 350-mA Constant On-Time Buck Switching Regulator data sheet.