SPRS825F October   2012  – June 2020 F28M36H33B2 , F28M36H53B2 , F28M36P53C2 , F28M36P63C2

PRODUCTION DATA.  

  1. 1Device Overview
    1. 1.1 Features
    2. 1.2 Applications
    3. 1.3 Description
    4. 1.4 Functional Block Diagram
  2. 2Revision History
  3. 3Device Comparison
    1. 3.1 Related Products
  4. 4Terminal Configuration and Functions
    1. 4.1 Pin Diagrams
    2. 4.2 Signal Descriptions
      1. Table 4-1 Signal Descriptions
  5. 5Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings – Commercial
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Power Consumption Summary
      1. Table 5-1 Current Consumption at 150-MHz C28x SYSCLKOUT and 75-MHz M3SSCLK
      2. Table 5-2 Current Consumption at 125-MHz C28x SYSCLKOUT and 125-MHz M3SSCLK
    5. 5.5  Electrical Characteristics
    6. 5.6  Thermal Resistance Characteristics for ZWT Package (Revision 0 Silicon)
    7. 5.7  Thermal Resistance Characteristics for ZWT Package (Revision A Silicon)
    8. 5.8  Thermal Design Considerations
    9. 5.9  Timing and Switching Characteristics
      1. 5.9.1 Power Sequencing
        1. Table 5-3 Reset (XRS) Timing Requirements
        2. Table 5-4 Reset (XRS) Switching Characteristics
        3. 5.9.1.1   Power Management and Supervisory Circuit Solutions
      2. 5.9.2 Clock Specifications
        1. 5.9.2.1 Changing the Frequency of the Main PLL
        2. 5.9.2.2 Input Clock Frequency and Timing Requirements, PLL Lock Times
          1. Table 5-5  Input Clock Frequency
          2. Table 5-7  Crystal Oscillator Electrical Characteristics
          3. Table 5-8  X1 Timing Requirements - PLL Enabled
          4. Table 5-9  X1 Timing Requirements - PLL Disabled
          5. Table 5-10 XCLKIN Timing Requirements - PLL Enabled
          6. Table 5-11 XCLKIN Timing Requirements - PLL Disabled
          7. Table 5-12 PLL Lock Times
        3. 5.9.2.3 Output Clock Frequency and Switching Characteristics
          1. Table 5-13 Output Clock Frequency
          2. Table 5-14 XCLKOUT Switching Characteristics (PLL Bypassed or Enabled)
        4. 5.9.2.4 Internal Clock Frequencies
          1. Table 5-15 Internal Clock Frequencies (150-MHz Devices)
      3. 5.9.3 Timing Parameter Symbology
        1. 5.9.3.1 General Notes on Timing Parameters
        2. 5.9.3.2 Test Load Circuit
      4. 5.9.4 Flash Timing – Master Subsystem
        1. Table 5-16 Master Subsystem – Flash/OTP Endurance
        2. Table 5-17 Master Subsystem – Flash Parameters
        3. Table 5-18 Master Subsystem – Flash/OTP Access Timing
        4. Table 5-19 Master Subsystem – Flash Data Retention Duration
      5. 5.9.5 Flash Timing – Control Subsystem
        1. Table 5-21 Control Subsystem – Flash/OTP Endurance
        2. Table 5-22 Control Subsystem – Flash Parameters
        3. Table 5-23 Control Subsystem – Flash/OTP Access Timing
        4. Table 5-24 Control Subsystem – Flash Data Retention Duration
      6. 5.9.6 GPIO Electrical Data and Timing
        1. 5.9.6.1 GPIO - Output Timing
          1. Table 5-26 General-Purpose Output Switching Characteristics
        2. 5.9.6.2 GPIO - Input Timing
          1. Table 5-27 General-Purpose Input Timing Requirements
        3. 5.9.6.3 Sampling Window Width for Input Signals
        4. 5.9.6.4 Low-Power Mode Wakeup Timing
          1. Table 5-28 IDLE Mode Timing Requirements
          2. Table 5-29 IDLE Mode Switching Characteristics
          3. Table 5-30 STANDBY Mode Timing Requirements
          4. Table 5-31 STANDBY Mode Switching Characteristics
          5. Table 5-32 HALT Mode Timing Requirements
          6. Table 5-33 HALT Mode Switching Characteristics
      7. 5.9.7 External Interrupt Electrical Data and Timing
        1. Table 5-34 External Interrupt Timing Requirements
        2. Table 5-35 External Interrupt Switching Characteristics
    10. 5.10 Analog and Shared Peripherals
      1. 5.10.1 Analog-to-Digital Converter
        1. 5.10.1.1 Sample Mode
        2. 5.10.1.2 Start-of-Conversion Triggers
        3. 5.10.1.3 Analog Inputs
        4. 5.10.1.4 ADC Result Registers and EOC Interrupts
        5. 5.10.1.5 ADC Electrical Data and Timing
          1. Table 5-36 ADC Electrical Characteristics
          2. Table 5-37 External ADC Start-of-Conversion Switching Characteristics
      2. 5.10.2 Comparator + DAC Units
        1. 5.10.2.1 On-Chip Comparator and DAC Electrical Data and Timing
          1. Table 5-38 Electrical Characteristics of the Comparator/DAC
      3. 5.10.3 Interprocessor Communications
      4. 5.10.4 External Peripheral Interface
        1. 5.10.4.1 EPI General-Purpose Mode
        2. 5.10.4.2 EPI SDRAM Mode
        3. 5.10.4.3 EPI Host Bus Mode
          1. 5.10.4.3.1 EPI 8-Bit Host Bus (HB-8) Mode
            1. 5.10.4.3.1.1 HB-8 Muxed Address/Data Mode
            2. 5.10.4.3.1.2 HB-8 Non-Muxed Address/Data Mode
            3. 5.10.4.3.1.3 HB-8 FIFO Mode
          2. 5.10.4.3.2 EPI 16-Bit Host Bus (HB-16) Mode
            1. 5.10.4.3.2.1 HB-16 Muxed Address/Data Mode
            2. 5.10.4.3.2.2 HB-16 Non-Muxed Address/Data Mode
            3. 5.10.4.3.2.3 HB-16 FIFO Mode
        4. 5.10.4.4 EPI Electrical Data and Timing
          1. Table 5-52 EPI SDRAM Interface Switching Characteristics (see , , and )
          2. Table 5-53 EPI Host-Bus 8 and Host-Bus 16 Interface Switching Characteristics (see , , , and )
          3. Table 5-54 EPI Host-Bus 8 and Host-Bus 16 Interface Timing Requirements (see and )
          4. Table 5-55 EPI General-Purpose Interface Switching Characteristics (see )
          5. Table 5-56 EPI General-Purpose Interface Timing Requirements (see and )
    11. 5.11 Master Subsystem Peripherals
      1. 5.11.1 Synchronous Serial Interface
        1. 5.11.1.1 Bit Rate Generation
        2. 5.11.1.2 Transmit FIFO
        3. 5.11.1.3 Receive FIFO
        4. 5.11.1.4 Interrupts
        5. 5.11.1.5 Frame Formats
      2. 5.11.2 Universal Asynchronous Receiver/Transmitter
        1. 5.11.2.1 Baud-Rate Generation
        2. 5.11.2.2 Transmit and Receive Logic
        3. 5.11.2.3 Data Transmission and Reception
        4. 5.11.2.4 Interrupts
      3. 5.11.3 Cortex-M3 Inter-Integrated Circuit
        1. 5.11.3.1 Functional Overview
        2. 5.11.3.2 Available Speed Modes
        3. 5.11.3.3 I2C Electrical Data and Timing
          1. Table 5-57 I2C Timing
      4. 5.11.4 Cortex-M3 Controller Area Network
        1. 5.11.4.1 Functional Overview
      5. 5.11.5 Cortex-M3 Universal Serial Bus Controller
        1. 5.11.5.1 Functional Description
      6. 5.11.6 Cortex-M3 Ethernet Media Access Controller
        1. 5.11.6.1 Functional Overview
        2. 5.11.6.2 MII Signals
        3. 5.11.6.3 EMAC Electrical Data and Timing
          1. Table 5-59 Timing Requirements for MIITXCK (see )
          2. Table 5-60 Timing Requirements for MIIRXCK (see )
          3. Table 5-61 Switching Characteristics for EMAC MII Transmit (see )
          4. Table 5-62 Timing Requirements for EMAC MII Receive (see )
        4. 5.11.6.4 MDIO Electrical Data and Timing
          1. Table 5-63 Switching Characteristics for MDIO_CK (see )
          2. Table 5-64 Switching Characteristics for MDIO as Output (see )
          3. Table 5-65 Timing Requirements for MDIO as Input (see )
    12. 5.12 Control Subsystem Peripherals
      1. 5.12.1 High-Resolution PWM and Enhanced PWM Modules
        1. 5.12.1.1 HRPWM Electrical Data and Timing
          1. Table 5-66 High-Resolution PWM Characteristics at SYSCLKOUT = (60–150 MHz)
        2. 5.12.1.2 ePWM Electrical Data and Timing
          1. Table 5-67 ePWM Timing Requirements
          2. Table 5-68 ePWM Switching Characteristics
          3. 5.12.1.2.1 Trip-Zone Input Timing
            1. Table 5-69 Trip-Zone Input Timing Requirements
      2. 5.12.2 Enhanced Capture Module
        1. 5.12.2.1 eCAP Electrical Data and Timing
          1. Table 5-70 eCAP Timing Requirement
          2. Table 5-71 eCAP Switching Characteristics
      3. 5.12.3 Enhanced Quadrature Encoder Pulse Module
        1. 5.12.3.1 eQEP Electrical Data and Timing
          1. Table 5-72 eQEP Timing Requirements
          2. Table 5-73 eQEP Switching Characteristics
      4. 5.12.4 C28x Inter-Integrated Circuit Module
        1. 5.12.4.1 Functional Overview
        2. 5.12.4.2 Clock Generation
        3. 5.12.4.3 I2C Electrical Data and Timing
          1. Table 5-74 I2C Timing
      5. 5.12.5 C28x Serial Communications Interface
        1. 5.12.5.1 Architecture
        2. 5.12.5.2 Multiprocessor and Asynchronous Communication Modes
      6. 5.12.6 C28x Serial Peripheral Interface
        1. 5.12.6.1 Functional Overview
        2. 5.12.6.2 SPI Electrical Data and Timing
          1. 5.12.6.2.1 Master Mode Timing
            1. Table 5-75 SPI Master Mode External Timing (Clock Phase = 0)
            2. Table 5-76 SPI Master Mode External Timing (Clock Phase = 1)
          2. 5.12.6.2.2 Slave Mode Timing
            1. Table 5-77 SPI Slave Mode External Timing (Clock Phase = 0)
            2. Table 5-78 SPI Slave Mode External Timing (Clock Phase = 1)
      7. 5.12.7 C28x Multichannel Buffered Serial Port
        1. 5.12.7.1 McBSP Electrical Data and Timing
          1. 5.12.7.1.1 McBSP Transmit and Receive Timing
            1. Table 5-79 McBSP Timing Requirements
            2. Table 5-80 McBSP Switching Characteristics
          2. 5.12.7.1.2 McBSP as SPI Master or Slave Timing
            1. Table 5-81 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 0)
            2. Table 5-82 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 0)
            3. Table 5-83 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 0)
            4. Table 5-84 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 0)
            5. Table 5-85 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 1)
            6. Table 5-86 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 1)
            7. Table 5-87 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 1)
            8. Table 5-88 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 1)
  6. 6Detailed Description
    1. 6.1  Memory Maps
      1. 6.1.1 Control Subsystem Memory Map
      2. 6.1.2 Master Subsystem Memory Map
    2. 6.2  Identification
    3. 6.3  Master Subsystem
      1. 6.3.1 Cortex-M3 CPU
      2. 6.3.2 Cortex-M3 DMA and NVIC
      3. 6.3.3 Cortex-M3 Interrupts
      4. 6.3.4 Cortex-M3 Vector Table
      5. 6.3.5 Cortex-M3 Local Peripherals
      6. 6.3.6 Cortex-M3 Local Memory
      7. 6.3.7 Cortex-M3 Accessing Shared Resources and Analog Peripherals
    4. 6.4  Control Subsystem
      1. 6.4.1 C28x CPU/FPU/VCU
      2. 6.4.2 C28x Core Hardware Built-In Self-Test
      3. 6.4.3 C28x Peripheral Interrupt Expansion
      4. 6.4.4 C28x Direct Memory Access
      5. 6.4.5 C28x Local Peripherals
      6. 6.4.6 C28x Local Memory
      7. 6.4.7 C28x Accessing Shared Resources and Analog Peripherals
    5. 6.5  Analog Subsystem
      1. 6.5.1 ADC1
      2. 6.5.2 ADC2
      3. 6.5.3 Analog Comparator + DAC
      4. 6.5.4 Analog Common Interface Bus
    6. 6.6  Master Subsystem NMIs
    7. 6.7  Control Subsystem NMIs
    8. 6.8  Resets
      1. 6.8.1 Cortex-M3 Resets
      2. 6.8.2 C28x Resets
      3. 6.8.3 Analog Subsystem and Shared Resources Resets
      4. 6.8.4 Device Boot Sequence
    9. 6.9  Internal Voltage Regulation and Power-On-Reset Functionality
      1. 6.9.1 Analog Subsystem: Internal 1.8-V VREG
      2. 6.9.2 Digital Subsystem: Internal 1.2-V VREG
      3. 6.9.3 Analog and Digital Subsystems: Power-On-Reset Functionality
      4. 6.9.4 Connecting ARS and XRS Pins
    10. 6.10 Input Clocks and PLLs
      1. 6.10.1 Internal Oscillator (Zero-Pin)
      2. 6.10.2 Crystal Oscillator/Resonator (Pins X1/X2 and VSSOSC)
      3. 6.10.3 External Oscillators (Pins X1, VSSOSC, XCLKIN)
      4. 6.10.4 Main PLL
      5. 6.10.5 USB PLL
    11. 6.11 Master Subsystem Clocking
      1. 6.11.1 Cortex-M3 Run Mode
      2. 6.11.2 Cortex-M3 Sleep Mode
      3. 6.11.3 Cortex-M3 Deep Sleep Mode
    12. 6.12 Control Subsystem Clocking
      1. 6.12.1 C28x Normal Mode
      2. 6.12.2 C28x IDLE Mode
      3. 6.12.3 C28x STANDBY Mode
    13. 6.13 Analog Subsystem Clocking
    14. 6.14 Shared Resources Clocking
    15. 6.15 Loss of Input Clock (NMI Watchdog Function)
    16. 6.16 GPIOs and Other Pins
      1. 6.16.1 GPIO_MUX1
      2. 6.16.2 GPIO_MUX2
      3. 6.16.3 AIO_MUX1
      4. 6.16.4 AIO_MUX2
    17. 6.17 Emulation/JTAG
    18. 6.18 Code Security Module
      1. 6.18.1 Functional Description
    19. 6.19 µCRC Module
      1. 6.19.1 Functional Description
      2. 6.19.2 CRC Polynomials
      3. 6.19.3 CRC Calculation Procedure
      4. 6.19.4 CRC Calculation for Data Stored In Secure Memory
  7. 7Applications, Implementation, and Layout
    1. 7.1 TI Reference Design
  8. 8Device and Documentation Support
    1. 8.1 Device and Development Support Tool Nomenclature
    2. 8.2 Tools and Software
    3. 8.3 Documentation Support
    4. 8.4 Related Links
    5. 8.5 Support Resources
    6. 8.6 Trademarks
    7. 8.7 Electrostatic Discharge Caution
    8. 8.8 Glossary
  9. 9Mechanical, Packaging, and Orderable Information
    1. 9.1 Packaging Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

Table 5-31 STANDBY Mode Switching Characteristics

over recommended operating conditions (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN MAX UNIT
td(IDLE-XCOL) Delay time, IDLE instruction executed to XCLKOUT low 32tc(SCO) 45tc(SCO) cycles
td(WAKE-STBY) Delay time, external wake signal to program execution resume(1) cycles
  • Wake up from flash
    • Flash module in active state
 Without input qualifier 100tc(SCO) cycles
With input qualifier 100tc(SCO) + tw(WAKE-INT)
  • Wake up from flash
    • Flash module in sleep state
 Without input qualifier 1125tc(SCO) cycles
With input qualifier 1125tc(SCO) + tw(WAKE-INT)
  • Wake up from SARAM
 Without input qualifier 100tc(SCO) cycles
With input qualifier 100tc(SCO) + tw(WAKE-INT)
(1) This is the time taken to begin execution of the instruction that immediately follows the IDLE instruction. execution of an ISR (triggered by the wake up signal) involves additional latency.
F28M36P63C2 F28M36P53C2 F28M36H53B2 F28M36H33B2 td_stdby_prs825.gif
A. IDLE instruction is executed to put the device into STANDBY mode.
B. The PLL block responds to the STANDBY signal. SYSCLKOUT is held for the number of cycles indicated below before being turned off:
  • 16 cycles, when DIVSEL = 00 or 01
  • 32 cycles, when DIVSEL = 10
  • 64 cycles, when DIVSEL = 11

    • This delay enables the CPU pipeline and any other pending operations to flush properly. If an access to XINTF is in progress and its access time is longer than this number then it will fail.  It is recommended to enter STANDBY mode from SARAM without an XINTF access in progress.

C. Clock to the peripherals are turned off. However, the PLL and watchdog are not shut down. The device is now in STANDBY mode.
D. The external wake-up signal is driven active.
E. After a latency period, the STANDBY mode is exited.
F. Normal execution resumes. The device will respond to the interrupt (if enabled).
G. From the time the IDLE instruction is executed to place the device into low-power mode, wakeup should not be initiated until at least 4 OSCCLK cycles have elapsed.
Figure 5-8 STANDBY Entry and Exit Timing Diagram