JAJSEX5B August   2010  – March 2018 LM3535

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      代表的なアプリケーション
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Charge Pump
      2. 8.3.2 Diode Current Sinks
      3. 8.3.3 Ambient Light Sensing (ALS) And Interrupt
      4. 8.3.4 Dynamic Backlight Control Input (PWM Pin)
      5. 8.3.5 LED Forward Voltage Monitoring
      6. 8.3.6 Configurable Gain Transition Delay
      7. 8.3.7 Hardware Enable (HWEN)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Shutdown
      2. 8.4.2 Standby
      3. 8.4.3 Active Mode
    5. 8.5 Programming
      1. 8.5.1 I2C Compatible Interface
        1. 8.5.1.1 Data Validity
        2. 8.5.1.2 Start and Stop Conditions
        3. 8.5.1.3 Transferring Data
        4. 8.5.1.4 I2C Compatible Chip Address
        5. 8.5.1.5 Internal Registers of LM3535
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Ambient Light Sensing
          1. 9.2.2.1.1 Ambient Light Sensor Block
          2. 9.2.2.1.2 ALS Operation
            1. 9.2.2.1.2.1 ALS Configuration Example
          3. 9.2.2.1.3 ALS Averaging Time
          4. 9.2.2.1.4 Ambient Light Current Control + PWM
            1. 9.2.2.1.4.1 ALS + PWM Example
        2. 9.2.2.2 LED Configurations
        3. 9.2.2.3 Maximum Output Current, Maximum LED Voltage, Minimum Input Voltage
          1. 9.2.2.3.1 Total Output Current Capability
        4. 9.2.2.4 Parallel Connected and Unused Outputs
        5. 9.2.2.5 Power Efficiency
        6. 9.2.2.6 Power Dissipation
        7. 9.2.2.7 Thermal Protection
        8. 9.2.2.8 Capacitor Selection
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 ドキュメントの更新通知を受け取る方法
    2. 12.2 コミュニティ・リソース
    3. 12.3 商標
    4. 12.4 静電気放電に関する注意事項
    5. 12.5 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.2.2.4 Parallel Connected and Unused Outputs

Connecting the outputs in parallel does not affect internal operation of the LM3535 and has no impact on the Electrical Characteristics and limits previously presented. The available diode output current, maximum diode voltage, and all other specifications provided in the Electrical Characteristics table apply to this parallel output configuration, just as they do to the standard LED application circuit.

All Dx current sinks utilize LED forward voltage sensing circuitry to optimize the charge-pump gain for maximum efficiency. Due to the nature of the sensing circuitry, TI recommends not leaving any of the Dx pins open when the current sinks are enabled (ENx bits are set to 1). Leaving Dx pins unconnected forces the charge-pump into 3/2× mode over the entire VIN range negating any efficiency gain that could have been achieved by switching to 1× mode at higher input voltages.

If the D1B or D1C drivers are not going to be used, make sure that the ENB and ENC bits in the general purpose register are set to 0 to ensure optimal efficiency.