SNVS594G December   2008  – April 2016 LM3555

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Control Interface Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Synchronous Boost Converter
      2. 7.3.2  High-Side Current Source
      3. 7.3.3  I2C/EN Pin
      4. 7.3.4  SDA/EN2 and SCL/EN1 Pins
      5. 7.3.5  STROBE Pin
      6. 7.3.6  TORCH Pin
      7. 7.3.7  Indicator LED Pin (IND)
      8. 7.3.8  Internal Diode Detection
      9. 7.3.9  Fault Protections
        1. 7.3.9.1 Output Overvoltage Protection (OVP)
        2. 7.3.9.2 Output and LED Short-Circuit Protection (SCP)
        3. 7.3.9.3 Overtemperature Protection (OTP)
        4. 7.3.9.4 Flash Timeout (FTP)
        5. 7.3.9.5 Indicator Fault (IF)
        6. 7.3.9.6 Broken Inductor Fault (IP)
      10. 7.3.10 Undervoltage Lockout (UVLO)
      11. 7.3.11 Power-On Reset (POR)
    4. 7.4 Device Functional Modes
      1. 7.4.1 Single LED Operation
      2. 7.4.2 Dual LED Operation
      3. 7.4.3 Torch or Assist (Continuous Current) Operation
      4. 7.4.4 Flash (Pulsed Current) Operation
      5. 7.4.5 Indicator Operation
      6. 7.4.6 Simple Control State Diagram
    5. 7.5 Programming
      1. 7.5.1 I2C-Compatible Interface
        1. 7.5.1.1 Data Validity
        2. 7.5.1.2 Start and Stop Conditions
        3. 7.5.1.3 Transferring Data
        4. 7.5.1.4 I2C-Compatible Chip Address
    6. 7.6 Register Maps
      1. 7.6.1 Internal Registers of LM3555
      2. 7.6.2 Register Definitions
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Inductor Current Limit
        2. 8.2.2.2 Inductor Selection
        3. 8.2.2.3 Capacitor Selection
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Community Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation.