JAJSOR1E June   2022  – August 2024 LM5177

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 Handling Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1 Gate Driver Rise Time and Fall Time
    2. 6.2 Gate Driver Dead (Transition) Time
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Power-On Reset (POR System)
      2. 7.3.2  Buck-Boost Control Scheme
        1. 7.3.2.1 Boost Mode
        2. 7.3.2.2 Buck Mode
        3. 7.3.2.3 Buck-Boost Mode
      3. 7.3.3  Power Save Mode
      4. 7.3.4  Supply Voltage Selection – VMAX Switch
      5. 7.3.5  Enable and Undervoltage Lockout
      6. 7.3.6  Oscillator Frequency Selection
      7. 7.3.7  Frequency Synchronization
      8. 7.3.8  Voltage Regulation Loop
      9. 7.3.9  Output Voltage Tracking
      10. 7.3.10 Slope Compensation
      11. 7.3.11 Configurable Soft Start
      12. 7.3.12 Peak Current Sensor
      13. 7.3.13 Current Monitoring and Current Limit Control Loop
      14. 7.3.14 Short Circuit - Hiccup Protection
      15. 7.3.15 nFLT Pin and Protections
      16. 7.3.16 Device Configuration Pin
      17. 7.3.17 Dual Random Spread Spectrum – DRSS
      18. 7.3.18 Gate Driver
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1  Custom Design with WEBENCH Tools
        2. 8.2.2.2  Frequency
        3. 8.2.2.3  Feedback Divider
        4. 8.2.2.4  Inductor and Current Sense Resistor Selection
        5. 8.2.2.5  Slope Compensation
        6. 8.2.2.6  Output Capacitor
        7. 8.2.2.7  Input Capacitor
        8. 8.2.2.8  UVLO Divider
        9. 8.2.2.9  Soft-Start Capacitor
        10. 8.2.2.10 MOSFETs QH1 and QL1
        11. 8.2.2.11 MOSFETs QH2 and QL2
        12. 8.2.2.12 Frequency Compensation
        13. 8.2.2.13 External Component Selection
      3. 8.2.3 Application Curves
    3. 8.3 System Examples
      1. 8.3.1 Bi-Directional Power Backup
      2. 8.3.2 Parallel (Multiphase) Operation
  10. 9 Power Supply Recommendations
  11. 10Layout
    1. 10.1 Layout Guidelines
      1. 10.1.1 Power Stage Layout
      2. 10.1.2 Gate Driver Layout
      3. 10.1.3 Controller Layout
    2. 10.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 サード・パーティ製品に関する免責事項
      2. 11.1.2 Development Support
        1. 11.1.2.1 Custom Design with WEBENCH Tools
    2. 11.2 ドキュメントの更新通知を受け取る方法
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 静電気放電に関する注意事項
    6. 11.6 用語集
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

12 Revision History

Changes from Revision D (August 2023) to Revision E (August 2024)

  • Removed misleading sentence from MODE pin description: "If this function is not used, connect the pin to VCC or GND."Go
  • Adjusted max parameter value for HB1 to SW1 and HB2 to SW2 from 7.8V to 6.4VGo
  • Changed reference to PGND and fixed lower limit for LO1, LO2, to PGND (DC) from -5V to -0.3V Go
  • Added HOx to SWx parameterGo
  • Fixed title of Figure 6-20Go
  • Updated description for the enter condition of Buck-Boost mode (Buck and Boost mode entry was swapped)Go
  • Use upper case D for duty cycle Go
  • Updated calculation of CSA/CSB filter to use minimum ontimeGo
  • Aligned R_CFG setting 3 with value in Recommended Operating ConditionsGo
  • Fixed link to Quickstart CalculatorGo
  • Added system example for Parallel (Multiphase) OperationGo

Changes from Revision C (May 2023) to Revision D (August 2023)

  • デバイスのステータスをカタログ リリースに更新。Go
  • Adjusted min Vin and Iout for design exampleGo
  • Changed RT/SYNC to RTGo
  • Updated FB Pin Resistor table to show components with 3 digits valuesGo
  • Updated Inductor and Current Sense Resistor selection chapterGo
  • Replaced "slope capacitor" with "slope resistor"Go
  • Updated minimum Vin for UVLO Resistor calculationGo
  • Added reference to MOSFET in schematicGo
  • Added reference to MOSFET in schematicGo
  • Adjusted components to updated design parametersGo
  • Adjusted components to updated design parametersGo

Changes from Revision B (December 2022) to Revision C (May 2023)

  • デバイスのステータスを「事前情報」から「量産データ」に変更Go
  • Added Section for peak current sensorGo