JAJSLV7A October   2022  – December 2022 LMG2610

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  7. 7 Parameter Measurement Information
    1. 7.1 GaN Power FET Switching Parameters
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  GaN Power FET Switching Capability
      2. 8.3.2  Turn-On Slew-Rate Control
      3. 8.3.3  Current-Sense Emulation
      4. 8.3.4  Bootstrap Diode Function
      5. 8.3.5  Input Control Pins (EN, INL, INH)
      6. 8.3.6  INL - INH Interlock
      7. 8.3.7  AUX Supply Pin
        1. 8.3.7.1 AUX Power-On Reset
        2. 8.3.7.2 AUX Under-Voltage Lockout (UVLO)
      8. 8.3.8  BST Supply Pin
        1. 8.3.8.1 BST Power-On Reset
        2. 8.3.8.2 BST Under-Voltage Lockout (UVLO)
      9. 8.3.9  Over-Current Protection
      10. 8.3.10 Over-Temperature Protection
      11. 8.3.11 Fault Reporting
    4. 8.4 Device Functional Modes
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Turn-On Slew-Rate Design
        2. 9.2.2.2 Current-Sense Design
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
        1. 9.4.1.1 Solder-Joint Stress Relief
        2. 9.4.1.2 Signal-Ground Connection
        3. 9.4.1.3 CS Pin Signal
      2. 9.4.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  11. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
  • RRG|40
サーマルパッド・メカニカル・データ
発注情報

9.4.1.1 Solder-Joint Stress Relief

Large QFN packages can experience high solder-joint stress. Several best practices are recommended to provide solder-joint stress relief. First, the instructions for the NC1, NC2, and NC3 anchor pins found in Table 5-1 must be followed. Second, all the board solder pads must be non-solder-mask defined (NSMD) as shown in the land pattern example in the Mechanical Data. Finally, any board trace connected to an NSMD pad must be less than 2/3 the width of the pad on the pad side where it is connected. The trace must maintain this 2/3 width limit for as long as it is not covered by solder mask. After the trace is under solder mask, there are no limits on the trace dimensions. All these recommendations are followed in the Layout Example.