JAJSGN6A December   2019  – August 2021 LP875701-Q1

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Serial Bus Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Descriptions
      1. 7.3.1 Multi-Phase DC/DC Converters
        1. 7.3.1.1 Overview
        2. 7.3.1.2 Multiphase Switcher Configurations
        3. 7.3.1.3 Buck Converter Load-Current Measurement
        4. 7.3.1.4 Spread-Spectrum Mode
      2. 7.3.2 Sync Clock Functionality
      3. 7.3.3 Power-Up
      4. 7.3.4 Regulator Control
        1. 7.3.4.1 Enabling and Disabling Regulators
      5. 7.3.5 Enable and Disable Sequences
      6. 7.3.6 Device Reset Scenarios
      7. 7.3.7 Diagnosis and Protection Features
        1. 7.3.7.1 Power-Good Information (PGOOD pin)
        2. 7.3.7.2 Warnings for Diagnosis (Interrupt)
          1. 7.3.7.2.1 Output Power Limit
          2. 7.3.7.2.2 Thermal Warning
        3. 7.3.7.3 Protection (Regulator Disable)
          1. 7.3.7.3.1 Short-Circuit and Overload Protection
          2. 7.3.7.3.2 Overvoltage Protection
          3. 7.3.7.3.3 Thermal Shutdown
        4. 7.3.7.4 Fault (Power Down)
          1. 7.3.7.4.1 Undervoltage Lockout
      8. 7.3.8 GPIO Signal Operation
      9. 7.3.9 Digital Signal Filtering
    4. 7.4 Device Functional Modes
      1. 7.4.1 Modes of Operation
    5. 7.5 Programming
      1. 7.5.1 I2C-Compatible Interface
        1. 7.5.1.1 Data Validity
        2. 7.5.1.2 Start and Stop Conditions
        3. 7.5.1.3 Transferring Data
        4. 7.5.1.4 I2C-Compatible Chip Address
        5. 7.5.1.5 Auto-Increment Feature
    6. 7.6 Register Maps
      1. 7.6.1 Register Descriptions
        1.       53
        2. 7.6.1.1  DEV_REV
        3. 7.6.1.2  OTP_REV
        4. 7.6.1.3  BUCK0_CTRL1
        5. 7.6.1.4  BUCK0_DELAY
        6. 7.6.1.5  GPIO2_DELAY
        7. 7.6.1.6  GPIO3_DELAY
        8. 7.6.1.7  RESET
        9. 7.6.1.8  CONFIG
        10. 7.6.1.9  INT_TOP1
        11. 7.6.1.10 INT_TOP2
        12. 7.6.1.11 INT_BUCK_0_1
        13. 7.6.1.12 INT_BUCK_2_3
        14. 7.6.1.13 TOP_STAT
        15. 7.6.1.14 BUCK_0_1_STAT
        16. 7.6.1.15 BUCK_2_3_STAT
        17. 7.6.1.16 TOP_MASK1
        18. 7.6.1.17 TOP_MASK2
        19. 7.6.1.18 BUCK_0_1_MASK
        20. 7.6.1.19 BUCK_2_3_MASK
        21. 7.6.1.20 SEL_I_LOAD
        22. 7.6.1.21 I_LOAD_2
        23. 7.6.1.22 I_LOAD_1
        24. 7.6.1.23 PGOOD_CTRL1
        25. 7.6.1.24 PGOOD_CTRL2
        26. 7.6.1.25 PGOOD_FLT
        27. 7.6.1.26 PLL_CTRL
        28. 7.6.1.27 PIN_FUNCTION
        29. 7.6.1.28 GPIO_CONFIG
        30. 7.6.1.29 GPIO_IN
        31. 7.6.1.30 GPIO_OUT
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
        1. 8.2.1.1 Inductor Selection
        2. 8.2.1.2 Input Capacitor Selection
        3. 8.2.1.3 Output Capacitor Selection
        4. 8.2.1.4 Snubber Components
        5. 8.2.1.5 Supply Filtering Components
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 サポート・リソース
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.6.1.17 TOP_MASK2

Address: 0x22

D7 D6 D5 D4 D3 D2 D1 D0
Reserved RESET_REG
_MASK
Bits Field Type Default Description
7:1 Reserved R/W 0h
0 RESET_REG_MASK R/W X Masking for the register reset interrupt (the RESET_REG bit in the INT_TOP2 register)
0h = Interrupt generated
1h = Interrupt not generated