JAJSKS9 December   2020 PCM6480-Q1

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics
    6. 7.6  Timing Requirements: I2C Interface
    7. 7.7  Switching Characteristics: I2C Interface
    8. 7.8  Timing Requirements: SPI Interface
    9. 7.9  Switching Characteristics: SPI Interface
    10. 7.10 Timing Requirements: TDM, I2S or LJ Interface
    11. 7.11 Switching Characteristics: TDM, I2S or LJ Interface
    12. 7.12 Timing Requirements: PDM Digital Microphone Interface
    13. 7.13 Switching Characteristics: PDM Digial Microphone Interface
    14. 7.14 Timing Diagrams
    15. 7.15 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Serial Interfaces
        1. 8.3.1.1 Control Serial Interfaces
        2. 8.3.1.2 Audio Serial Interfaces
          1. 8.3.1.2.1 Time Division Multiplexed Audio (TDM) Interface
          2. 8.3.1.2.2 Inter IC Sound (I2S) Interface
          3. 8.3.1.2.3 Left-Justified (LJ) Interface
        3. 8.3.1.3 Using Multiple Devices With Shared Buses
      2. 8.3.2  Phase-Locked Loop (PLL) and Clock Generation
      3. 8.3.3  Analog Input Channel Configuration
      4. 8.3.4  Reference Voltage
      5. 8.3.5  Microphone Bias
      6. 8.3.6  Input DC Fault Diagnostics
        1. 8.3.6.1 Fault Conditions
          1. 8.3.6.1.1 Input Pin Short to Ground
          2. 8.3.6.1.2 Input Pin Short to MICBIAS
          3. 8.3.6.1.3 Open Inputs
          4. 8.3.6.1.4 Short Between INxP and INxM
          5. 8.3.6.1.5 Input Pin Overvoltage
          6. 8.3.6.1.6 Input Pin Short to VBAT_IN
        2. 8.3.6.2 Fault Reporting
          1. 8.3.6.2.1 Overcurrent and Overtemperature Protection
      7. 8.3.7  Digital PDM Microphone Record Channel
      8. 8.3.8  Signal-Chain Processing
        1. 8.3.8.1 Programmable Channel Gain and Digital Volume Control
        2. 8.3.8.2 Programmable Channel Gain Calibration
        3. 8.3.8.3 Programmable Channel Phase Calibration
        4. 8.3.8.4 Programmable Digital High-Pass Filter
        5. 8.3.8.5 Programmable Digital Biquad Filters
        6. 8.3.8.6 Programmable Channel Summer and Digital Mixer
        7. 8.3.8.7 Configurable Digital Decimation Filters
          1. 8.3.8.7.1 Linear Phase Filters
            1. 8.3.8.7.1.1 Sampling Rate: 8 kHz or 7.35 kHz
            2. 8.3.8.7.1.2 Sampling Rate: 16 kHz or 14.7 kHz
            3. 8.3.8.7.1.3 Sampling Rate: 24 kHz or 22.05 kHz
            4. 8.3.8.7.1.4 Sampling Rate: 32 kHz or 29.4 kHz
            5. 8.3.8.7.1.5 Sampling Rate: 48 kHz or 44.1 kHz
            6. 8.3.8.7.1.6 Sampling Rate: 96 kHz or 88.2 kHz
            7. 8.3.8.7.1.7 Sampling Rate: 192 kHz or 176.4 kHz
            8. 8.3.8.7.1.8 Sampling Rate: 384 kHz or 352.8 kHz
            9. 8.3.8.7.1.9 Sampling Rate: 768 kHz or 705.6 kHz
          2. 8.3.8.7.2 Low-Latency Filters
            1. 8.3.8.7.2.1 Sampling Rate: 16 kHz or 14.7 kHz
            2. 8.3.8.7.2.2 Sampling Rate: 24 kHz or 22.05 kHz
            3. 8.3.8.7.2.3 Sampling Rate: 32 kHz or 29.4 kHz
            4. 8.3.8.7.2.4 Sampling Rate: 48 kHz or 44.1 kHz
            5. 8.3.8.7.2.5 Sampling Rate: 96 kHz or 88.2 kHz
            6. 8.3.8.7.2.6 Sampling Rate: 192 kHz or 176.4 kHz
          3. 8.3.8.7.3 Ultra-Low-Latency Filters
            1. 8.3.8.7.3.1 Sampling Rate: 16 kHz or 14.7 kHz
            2. 8.3.8.7.3.2 Sampling Rate: 24 kHz or 22.05 kHz
            3. 8.3.8.7.3.3 Sampling Rate: 32 kHz or 29.4 kHz
            4. 8.3.8.7.3.4 Sampling Rate: 48 kHz or 44.1 kHz
            5. 8.3.8.7.3.5 Sampling Rate: 96 kHz or 88.2 kHz
            6. 8.3.8.7.3.6 Sampling Rate: 192 kHz or 176.4 kHz
            7. 8.3.8.7.3.7 Sampling Rate: 384 kHz or 352.8 kHz
      9. 8.3.9  Automatic Gain Controller (AGC)
      10. 8.3.10 Interrupts, Status, and Digital I/O Pin Multiplexing
    4. 8.4 Device Functional Modes
      1. 8.4.1 Hardware Shutdown
      2. 8.4.2 Sleep Mode or Software Shutdown
      3. 8.4.3 Active Mode
      4. 8.4.4 Software Reset
    5. 8.5 Programming
      1. 8.5.1 Control Serial Interfaces
        1. 8.5.1.1 I2C Control Interface
          1. 8.5.1.1.1 General I2C Operation
          2. 8.5.1.1.2 I2C Single-Byte and Multiple-Byte Transfers
            1. 8.5.1.1.2.1 I2C Single-Byte Write
            2. 8.5.1.1.2.2 I2C Multiple-Byte Write
            3. 8.5.1.1.2.3 I2C Single-Byte Read
            4. 8.5.1.1.2.4 I2C Multiple-Byte Read
        2. 8.5.1.2 SPI Control Interface
    6. 8.6 Register Maps
      1. 8.6.1 Device Configuration Registers
        1. 8.6.1.1 Registers Access Type
        2. 8.6.1.2 Page 0 Registers
        3. 8.6.1.3 Page 1 Registers
      2. 8.6.2 Programmable Coefficient Registers
        1. 8.6.2.1 Programmable Coefficient Registers: Page 2
        2. 8.6.2.2 Programmable Coefficient Registers: Page 3
        3. 8.6.2.3 Programmable Coefficient Registers: Page 4
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Four-Channel Analog Microphone and Four-Channel PDM Microphone Simultaneous Recording Using the PCM6480-Q1
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Example Device Register Configuration Script for EVM Setup
        3. 9.2.1.3 Application Curves
    3. 9.3 What To Do and What Not To Do
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Development Support
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 ドキュメントの更新通知を受け取る方法
    4. 12.4 サポート・リソース
    5. 12.5 Trademarks
    6. 12.6 静電気放電に関する注意事項
    7. 12.7 用語集
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報
8.3.6.1.6 Input Pin Short to VBAT_IN

A short to VBAT_IN fault occurs when the difference between the voltage measured for the VBAT_IN pin and the input pin, ABS(VBAT_IN – INxx), is less than the threshold or both the VBAT_IN and INxx pin measured voltages are above 11.7 V. The threshold can be set by configuring DIAG_SHT_VBAT_IN, P0_R101_D3-0.

When VBAT_IN is less than MICBIAS, false fault detections can exist based on the signal level of the INxx pin. To minimize false detections there is also a separate debounce count for this condition set by configuring VSHORT_DBNCE, P0_R106_D1.