SLLSE84D May   2011  – May 2017 SN65HVD101 , SN65HVD102

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Switching Characteristics
    7. 7.7 Typical Characteristics
  8. 8 Parameter Measurement
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Wake-up Detection
      2. 9.3.2 Current Limit Indication - Short Circuit Current Detection
      3. 9.3.3 Active Current Limit Condition: VTHL > VCQ ≥ VTHH
      4. 9.3.4 Inactive Current Limit Condition: VTHL < VCQ < VTHH
      5. 9.3.5 Over-temperature Detection
      6. 9.3.6 CQ Current-limit Adjustment
      7. 9.3.7 Transceiver Function Tables
      8. 9.3.8 Voltage Regulator (Not Available in SN65HVD102)
    4. 9.4 Device Functional Modes
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Transceiver Configuration (SN65HVD101)
        2. 10.2.2.2 Maximum Ambient Temperature Check
        3. 10.2.2.3 Transient Protection
        4. 10.2.2.4 TVS Evaluation
      3. 10.2.3 Application Curves
    3. 10.3 System Examples
      1. 10.3.1 Driver for Incandescent Lamp Loads
      2. 10.3.2 Driver for Inductive Loads
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Related Links
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 Community Resources
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6 Pin Configuration and Functions

RGB Package
20-Pin QFN with Thermal Pad
Top View
SN65HVD101 SN65HVD102 po_SLLSE84.gif

Pin Functions

PIN DESCRIPTION
NAME NUMBER TYPE(1)
IO-Link Interface
L+ 10 P IO-Link supply voltage (24V nominal)
CQ 12 I/O IO-Link data signal (bi-directional)
L– 14 P IO-Link ground (connect to board ground)
Local Controller Interface
CUR_OK 15 OD High-CQ-current fault indicator output signal from PHY to the microcontroller. Connect this pin via pull-up resistor to Vcc OUT. A LOW level indicates over-current condition.
WAKE 16 OD Wake up indicator from the PHY to the local controller Connect this pin via pull-up resistor to Vcc OUT.
RX 17 O PHY receive data output to the local controller
TX 18 I PHY transmit data input from the local controller
EN 20 I Driver enable input signal from the local controller
Power Supply Pins
VCC IN 7 A Voltage supply input for SN65HVD102
Voltage sense feedback input for the voltage regulator of the SN65HVD101. Connect this pin to pin 8 either directly or through a current boost transistor.
VCC OUT 8 P Not connected in SN65HVD102
Linear regulator output of SN65HVD101. Connect this pin to pin 7 either directly or through a current boost transistor.
GND 3, 6, 13 P Logic ground potential
Special Connect Pins
VCC SET 1 I Connect this pin to ground to make Vcc OUT = 3.3V. Leave this pin floating to make Vcc OUT = 5V.
ILIMADJ 4 A Input for current limit adjustment. Connect resistor RSET between this pin and ground. For RSET values see Figure 2.
PWR_OK 5 OD Power-Good indicator. Connect this pin via pull-up resistor to Vcc OUT. A HIGH at this pin indicates that L+ and Vcc OUT are at correct levels.
Temp_OK 19 OD Temperature-Good indicator. Connect this pin via pull-up resistor to Vcc OUT. High-impedance at this pin indicates that the internal temperature is at a safe level. A low at this pin indicates the device is approaching thermal shutdown.
NC 2, 9, 11 – No Connection. Leave these pins floating (open)
(1) Type definitions: I = Input, I/O = Input/Output, A = Analog, O - CMOS Output, OD = Open Drain Output, P = Power