JAJSNO9 January   2022 TAA5212

ADVANCE INFORMATION  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Timing Requirements: I2C Interface
    7. 6.7  Switching Characteristics: I2C Interface
    8. 6.8  Timing Requirements: SPI Interface
    9. 6.9  Switching Characteristics: SPI Interface
    10. 6.10 Timing Requirements: TDM, I2S or LJ Interface
    11. 6.11 Switching Characteristics: TDM, I2S or LJ Interface
    12. 6.12 Timing Requirements: PDM Digital Microphone Interface
    13. 6.13 Switching Characteristics: PDM Digial Microphone Interface
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Hardware Control
      2. 8.3.2 Serial Interfaces
        1. 8.3.2.1 Control Serial Interfaces
        2. 8.3.2.2 Audio Serial Interfaces
          1. 8.3.2.2.1 Time Division Multiplexed Audio (TDM) Interface
          2. 8.3.2.2.2 Inter IC Sound (I2S) Interface
          3. 8.3.2.2.3 Left-Justified (LJ) Interface
        3. 8.3.2.3 Using Multiple Devices With Shared Buses
      3. 8.3.3 Phase-Locked Loop (PLL) and Clock Generation
      4. 8.3.4 Input Channel Configurations
      5. 8.3.5 Reference Voltage
      6. 8.3.6 Programmable Microphone Bias
      7. 8.3.7 Signal-Chain Processing
        1. 8.3.7.1 ADC Signal-Chain
          1. 8.3.7.1.1 Programmable Channel Gain and Digital Volume Control
          2. 8.3.7.1.2 Programmable Channel Gain Calibration
          3. 8.3.7.1.3 Programmable Channel Phase Calibration
          4. 8.3.7.1.4 Programmable Digital High-Pass Filter
          5. 8.3.7.1.5 Programmable Digital Biquad Filters
          6. 8.3.7.1.6 Programmable Channel Summer and Digital Mixer
          7. 8.3.7.1.7 Configurable Digital Decimation Filters
            1. 8.3.7.1.7.1 Linear Phase Filters
              1. 8.3.7.1.7.1.1 Sampling Rate: 16 kHz or 14.7 kHz
              2. 8.3.7.1.7.1.2 Sampling Rate: 24 kHz or 22.05 kHz
              3. 8.3.7.1.7.1.3 Sampling Rate: 32 kHz or 29.4 kHz
              4. 8.3.7.1.7.1.4 Sampling Rate: 48 kHz or 44.1 kHz
              5. 8.3.7.1.7.1.5 Sampling Rate: 96 kHz or 88.2 kHz
      8. 8.3.8 Interrupts, Status, and Digital I/O Pin Multiplexing
      9. 8.3.9 Programmable Channel Phase Calibration
    4. 8.4 Device Functional Modes
    5. 8.5 Register Maps
      1. 8.5.1 VEGA Registers
      2. 8.5.2 TAA5212 Registers
      3. 8.5.3 TAA5212 Registers
    6. 8.6 Feature Description
    7. 8.7 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Application
      2. 9.2.2 Design Requirements
      3. 9.2.3 Detailed Design Procedure
      4. 9.2.4 Application Performance Plots
      5. 9.2.5 What to Do and What Not to Do
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 ドキュメントの更新通知を受け取る方法
    3. 12.3 サポート・リソース
    4. 12.4 Trademarks
    5. 12.5 静電気放電に関する注意事項
    6. 12.6 用語集

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.5 Register Maps

This section describes the control registers for the device in detail. All these registers are eight bits in width and allocated to device configuration and programmable coefficients settings. These registers are mapped internally using a page scheme that can be controlled using either I2C or SPI communication to the device. Each page contains 128 bytes of registers. All device configuration registers are stored in page 0, page 1 and page 3. Page 0 is the default page setting at power up (and after a software reset). The device current page can be switch to a new desired page by using the PAGE[7:0] bits located in register 0 of every page.

Do not read from or write to reserved pages or reserved registers. Write only default values for the reserved bits in the valid registers.

The procedure for register access across pages is:

  • Select page N (write data N to register 0 regardless of the current page number)
  • Read or write data from or to valid registers in page N
  • Select the new page M (write data M to register 0 regardless of the current page number)
  • Read or write data from or to valid registers in page M
  • Repeat as needed