JAJSNO8A January   2022  – October 2024 TAA5242

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements: TDM, I2S or LJ Interface
    7. 5.7 Switching Characteristics: TDM, I2S or LJ Interface
    8. 5.8 Timing Diagrams
    9. 5.9 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Hardware Control
      2. 6.3.2 Audio Serial Interfaces
        1. 6.3.2.1 Time Division Multiplexed Audio (TDM) Interface
        2. 6.3.2.2 Inter IC Sound (I2S) Interface
        3. 6.3.2.3 Left-Justified (LJ) Interface
      3. 6.3.3 Phase-Locked Loop (PLL) and Clock Generation
      4. 6.3.4 Analog Input Configurations
      5. 6.3.5 Reference Voltage
      6. 6.3.6 Integrated Microphone Bias
      7. 6.3.7 Signal-Chain Processing
        1. 6.3.7.1 Configurable Digital Decimation Filters
          1. 6.3.7.1.1 Linear-phase filters
            1. 6.3.7.1.1.1 Sampling Rate: 8kHz or 7.35kHz
            2. 6.3.7.1.1.2 Sampling Rate: 16kHz or 14.7kHz
            3. 6.3.7.1.1.3 Sampling Rate: 24kHz or 22.05kHz
            4. 6.3.7.1.1.4 Sampling Rate: 32kHz or 29.4kHz
            5. 6.3.7.1.1.5 Sampling Rate: 48kHz or 44.1kHz
            6. 6.3.7.1.1.6 Sampling Rate: 96kHz or 88.2kHz
            7. 6.3.7.1.1.7 Sampling Rate: 192kHz or 176.4kHz
          2. 6.3.7.1.2 Low-latency Filters
            1. 6.3.7.1.2.1 Sampling Rate: 24kHz or 22.05kHz
            2. 6.3.7.1.2.2 Sampling Rate: 32kHz or 29.4kHz
            3. 6.3.7.1.2.3 Sampling Rate: 48kHz or 44.1kHz
            4. 6.3.7.1.2.4 Sampling Rate: 96kHz or 88.2kHz
            5. 6.3.7.1.2.5 Sampling Rate: 192kHz or 176.4kHz
        2. 6.3.7.2 Programmable Digital High-Pass Filter
    4. 6.4 Device Functional Modes
      1. 6.4.1 Active Mode
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Application
      2. 7.2.2 Design Requirements
      3. 7.2.3 Detailed Design Procedure
      4. 7.2.4 Application Performance Plots
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Documentation Support
      1. 8.1.1 Related Documentation
    2. 8.2 ドキュメントの更新通知を受け取る方法
    3. 8.3 サポート・リソース
    4. 8.4 Trademarks
    5. 8.5 静電気放電に関する注意事項
    6. 8.6 用語集
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6.3.7.2 Programmable Digital High-Pass Filter

To remove the DC offset component and attenuate the undesired low-frequency noise content in the record data, the device supports a high-pass filter (HPF). This HPF is constructed using the first-order infinite impulse response (IIR) filter, and is efficient enough to filter out possible DC components of the signal. The default cut-off frequency for this HPF is set to 1Hz at 48kHz sampling frequency and in Target I2S/LJ Mode, it is selectable between 1Hz and 12Hz at 48kHz sampling frequency as mentioned in Table 6-10. This is not a channel-independent filter setting but is globally applicable for all ADC channels. Section 6.3.7.2 shows the frequency response for the HPF with the two settings.

TAA5242 HPF Filter Frequency Response PlotFigure 6-37 HPF Filter Frequency Response Plot