JAJSI83H May   2012  – September 2024 TCA9548A

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 I2C Interface Timing Requirements
    7. 5.7 Reset Timing Requirements
    8. 5.8 Switching Characteristics
    9. 5.9 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
    4. 7.4 Device Functional Modes
      1. 7.4.1 RESET Input
      2. 7.4.2 Power-On Reset
    5. 7.5 Programming
      1. 7.5.1 I2C Interface
      2. 7.5.2 Device Address
      3. 7.5.3 Bus Transactions
        1. 7.5.3.1 Writes
        2. 7.5.3.2 Reads
      4. 7.5.4 Control Register
      5. 7.5.5 RESET Input
      6. 7.5.6 Power-On Reset
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 Power-On Reset Requirements
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 ドキュメントの更新通知を受け取る方法
    3. 9.3 サポート・リソース
    4. 9.4 商標
    5. 9.5 静電気放電に関する注意事項
    6. 9.6 用語集
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

5.5 Electrical Characteristics

VCC = 1.65 V to 5.5 V, over recommended operating free-air temperature ranges supported by Recommended Operating Conditions (unless otherwise noted) (1)
PARAMETER TEST CONDITIONS VCC MIN TYP (2) MAX UNIT
VPORR Power-on reset voltage, VCC rising No load, VI = VCC or GND(3) 1.2 1.5 V
VPORF Power-on reset voltage, VCC falling(4) No load, VI = VCC or GND(3) 0.8 1 V
Vo(sw) Switch output voltage Vi(sw) = VCC, ISWout = –100 μA 5 V 3.6 V
4.5 V to 5.5 V 2.6 4.5
3.3 V 1.9
3 V to 3.6 V 1.6 2.8
2.5 V 1.5
2.3 V to 2.7 V 1.1 2
1.8 V 1.1
1.65 V to 1.95 V 0.6 1.25
IOL SDA VOL = 0.4 V 1.65 V to 5.5 V 3 6 mA
VOL = 0.6 V 6 9
II SCL, SDA VI = VCC or GND(3) 1.65 V to 5.5 V –1 1 μA
SC7–SC0, SD7–SD0 –1 1
A2–A0 –1 1
RESET –1 1
ICC Operating mode fSCL = 400 kHz VI = VCC or GND(3), IO = 0 5.5 V 50 80 μA
3.6 V 20 35
2.7 V 11 20
1.65 V 6 10
fSCL = 100 kHz VI = VCC or GND(3), IO = 0 5.5 V 9 30
3.6 V 6 15
2.7 V 4 8
1.65 V 2 4
Standby mode Low inputs VI = GND(3), IO = 0, -40 ℃ ≤ TA ≤ 85 ℃ 5.5 V 0.2 2
3.6 V 0.1 2
2.7 V 0.1 1
1.65 V 0.1 1
High inputs VI = VCC, IO = 0, -40 ℃ ≤ TA ≤ 85 ℃ 5.5 V 0.2 2
3.6 V 0.1 2
2.7 V 0.1 1
1.65 V 0.1 1
Low and High Inputs Vi = Vcc or GND, Io = 0, 85 ℃ < TA ≤ 125 ℃ 3.6 V 1 2 μA
2.7 V 0.7 1.5 μA
1.65 V 0.4 1 μA
ΔICC Supply-current change SCL, SDA SCL or SDA input at 0.6 V,
Other inputs at VCC or GND(3)		 1.65 V to 5.5 V 3 20 μA
SCL or SDA input at VCC – 0.6 V,
Other inputs at VCC or GND(3)		 3 20
Ci A2–A0 VI = VCC or GND(3) 1.65 V to 5.5 V 4 5 pF
RESET 4 5
SCL VI = VCC or GND(3), Switch OFF 20 28
Cio(off)(5) SDA VI = VCC or GND(3), Switch OFF 1.65 V to 5.5 V 20 28 pF
SC7–SC0, SD7–SD0 5.5 7.5
RON Switch-on resistance VO = 0.4 V, IO = 15 mA 4.5 V to 5.5 V 4 10 20 Ω
3 V to 3.6 V 5 12 30
VO = 0.4 V, IO = 10 mA 2.3 V to 2.7 V 7 15 45
1.65 V to 1.95 V 10 25 70
(1) For operation between specified voltage ranges, refer to the worst-case parameter in both applicable ranges
(2) All typical values are at nominal supply voltage (1.8-, 2.5-,3.3-, or 5-V VCC), TA = 25°C
(3) RESET = VCC (held high) when all other input voltages, VI = GND.
(4) The power-on reset circuit resets the I2C bus logic with VCC < VPORF
(5) Cio(ON) depends on internal capacitance and external capacitance added to the SCn lines when channels(s) are ON.