JAJSVM2 November   2024 TDP142-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Power Supply Characteristics
    6. 5.6 Control I/O DC Electrical Characteristics
    7. 5.7 DP Electrical Characteristics
    8. 5.8 Switching Characteristics
    9. 5.9 Typical Characteristics
  7.   Parameter Measurement Information
  8. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 DisplayPort
      2. 6.3.2 Configuration Jumper Levels
      3. 6.3.3 Receiver Linear Equalization
    4. 6.4 Device Functional Modes
      1. 6.4.1 Device Configuration in GPIO Mode
      2. 6.4.2 Device Configuration in I2C Mode
      3. 6.4.3 Linear EQ Configuration
      4. 6.4.4 Operation Timing – Power Up
    5. 6.5 Programming
  9. 7 Register Maps
    1. 7.1 TDP142-Q1 Registers
  10. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 ESD Protection
    2. 8.2 Typical Application
      1. 8.2.1 Source Application Implementation
        1. 8.2.1.1 Design Requirement
        2. 8.2.1.2 Detail Design Procedure
      2. 8.2.2 Sink Application Implementation
        1. 8.2.2.1 Design Requirements
        2. 8.2.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curve
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  11. 9 Device and Documentation Support
    1. 9.1 ドキュメントの更新通知を受け取る方法
    2. 9.2 サポート・リソース
    3. 9.3 Trademarks
    4. 9.4 静電気放電に関する注意事項
    5. 9.5 用語集
  12. 10Revision History
  13. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Tape and Reel Information
    2. 11.2 Mechanical Data

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.1.1 ESD Protection

It may be necessary to incorporate an ESD component to protect the TDP142-Q1 from electrostatic discharge (ESD). TI recommends following the ESD protection recommendations listed in Table 8-1. A clamp voltage greater than value specified in Table 8-1 may require a RESD on each differential pin. Place the ESD component near the USB connector.

Table 8-1 ESD Diodes Recommended Characteristics
ParameterRecommendation
Breakdown voltage≥ 3.5V for DP input pins
≥ 1.5V for non-DP input pins
I/O line capacitanceData rates ≤ 5Gbps: ≤ 0.50pF
Data rates > 5Gbps: ≤ 0.35pF
Delta capacitance between any P and N I/O pins≤ 0.07pF
Clamping voltage at 8A IPP IO to GND(1)≤ 4.5V
Typical dynamic resistance≤ 30mΩ
(1) According to IEC 61000-4-5 (8/20μs current waveform)
Table 8-2 Recommended ESD Protection Component
ManufacturerPart NumberRESD to support IEC 61000-4-2 Contact ±8kV
NexperiaPUSB3FR41Ω
NexperiaPESD2V8Y1BSF1Ω
Texas InstrumentsTPD1E04U04DPLR2Ω
Texas InstrumentsTPD4E02B04DQAR2Ω