JAJSO93A May   2022  – December 2022 TLIN1431-Q1

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 ESD Ratings, IEC Specification
    4. 6.4 Recommended Operating Conditions
    5. 6.5 Thermal Information
    6. 6.6 Power Supply Characteristics
    7. 6.7 Electrical Characteristics
    8. 6.8 AC Switching Characteristics
    9. 6.9 Typical Characteristics
  7. 7 Parameter Measurement Information
    1. 7.1 Test Circuit: Diagrams and Waveforms
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  LIN (Local Interconnect Network) Bus
        1. 8.3.1.1 LIN Transmitter Characteristics
        2. 8.3.1.2 LIN Receiver Characteristics
          1. 8.3.1.2.1 Termination
      2. 8.3.2  TXD (Transmit Input and Output)
      3. 8.3.3  RXD (Receive Output)
      4. 8.3.4  WAKE (High Voltage Local Wake Up Input)
      5. 8.3.5  WDT or CLK (Pin Programmable Watchdog Delay Input or SPI Clock)
      6. 8.3.6  WDI or SDI (Watchdog Timer Input or SPI Serial Data In)
      7. 8.3.7  PIN or nCS (Pin Watchdog Select or SPI Chip Select)
      8. 8.3.8  LIMP (Limp Home Output – High Voltage Open Drain Output)
        1. 8.3.8.1 LIMP in Pin Control Mode
        2. 8.3.8.2 LIMP in SPI Control Mode
      9. 8.3.9  nWDR/SDO (Watchdog Timeout Reset Output/SPI Serial Data Out)
      10. 8.3.10 HSS (High-side Switch)
      11. 8.3.11 HSSC or FSO (High-side Switch Control or Function Output)
      12. 8.3.12 WKRQ or INH (Wake Request or Inhibit)
      13. 8.3.13 PV
      14. 8.3.14 DIV_ON
      15. 8.3.15 VBAT (Battery Voltage)
      16. 8.3.16 VSUP (Supply Voltage)
      17. 8.3.17 GND (Ground)
      18. 8.3.18 EN or nINT (Enable Input or Interrupt Output)
      19. 8.3.19 nRST (Reset Input and Reset Output)
      20. 8.3.20 VCC (Supply Output)
      21. 8.3.21 VBAT Voltage Divider
      22. 8.3.22 Protection Features
        1. 8.3.22.1  Sleep Wake Error (SWE) Timer
        2. 8.3.22.2  Device Reset
        3. 8.3.22.3  TXD Dominant Time Out (DTO)
        4. 8.3.22.4  Bus Stuck Dominant System Fault: False Wake Up Lockout
        5. 8.3.22.5  Thermal Shutdown
        6. 8.3.22.6  Under-voltage on VSUP
        7. 8.3.22.7  Unpowered Device and LIN Bus
        8. 8.3.22.8  Floating Pins
        9. 8.3.22.9  VCC Voltage Regulator
          1. 8.3.22.9.1 Under or Over Voltage and Short Circuit
          2. 8.3.22.9.2 Output Capacitance Selection
          3. 8.3.22.9.3 Low-Voltage Tracking
          4. 8.3.22.9.4 Power Supply Recommendation
        10. 8.3.22.10 Watchdog
          1. 8.3.22.10.1 Watchdog in Pin Control Mode
          2. 8.3.22.10.2 Watchdog in SPI Control Mode
          3. 8.3.22.10.3 Watchdog Error Counter
          4. 8.3.22.10.4 Pin Control Mode
          5. 8.3.22.10.5 SPI Control Programming
          6. 8.3.22.10.6 Watchdog Register Relationship
          7. 8.3.22.10.7 Watchdog Timing
      23. 8.3.23 Channel Expansion
        1. 8.3.23.1 Channel Expansion for LIN
        2. 8.3.23.2 Channel Expansion for CAN Transceiver
    4. 8.4 Device Functional Modes
      1. 8.4.1 Init Mode
      2. 8.4.2 Normal Mode
      3. 8.4.3 Fast Mode
      4. 8.4.4 Sleep Mode
      5. 8.4.5 Standby Mode
      6. 8.4.6 Restart Mode
        1. 8.4.6.1 Restart Counter
        2. 8.4.6.2 nRST Behavior in Restart Mode
      7. 8.4.7 Fail-safe Mode
      8. 8.4.8 Wake Up Events
        1. 8.4.8.1 Wake Up Request (RXD)
        2. 8.4.8.2 Local Wake Up (LWU) via WAKE Terminal
          1. 8.4.8.2.1 Static WAKE
          2. 8.4.8.2.2 Cyclic Sense Wake
      9. 8.4.9 Mode Transitions
    5. 8.5 Programming
      1. 8.5.1 SPI Communication
        1. 8.5.1.1 Cyclic Redundancy Check
        2. 8.5.1.2 Chip Select Not (nCS)
        3. 8.5.1.3 Serial Clock Input (CLK)
        4. 8.5.1.4 Serial Data Input (SDI)
        5. 8.5.1.5 Serial Data Output (SDO)
    6. 8.6 Registers
      1. 8.6.1  DEVICE_ID_y Register (Address = 0h + formula) [reset = 0h]
      2. 8.6.2  REV_ID_MAJOR Register (Address = 8h) [reset = 01h]
      3. 8.6.3  REV_ID_MINOR Register (Address = 9h) [reset = 0h]
      4. 8.6.4  CRC_CNTL Register (Address = Ah) [reset = 0h]
      5. 8.6.5  CRC_POLY_SET (Address = Bh) [reset = 00h]
      6. 8.6.6  Scratch_Pad_SPI Register (Address = Fh) [reset = 0h]
      7. 8.6.7  WAKE_PIN_CONFIG1 Register (Address = 11h) [reset = 04h]
      8. 8.6.8  WAKE_PIN_CONFIG2 Register (Address = 12h) [reset = 2h]
      9. 8.6.9  WD_CONFIG_1 Register (Address = 13h) [reset = 90h]
      10. 8.6.10 WD_CONFIG_2 Register (Address = 14h) [reset = 02h]
      11. 8.6.11 WD_INPUT_TRIG Register (Address = 15h) [reset = 0h]
      12. 8.6.12 WD_RST_PULSE Register (Address = 16h) [reset = 40h]
      13. 8.6.13 FSM_CONFIG Register (Address = 17h) [reset = 0h]
      14. 8.6.14 FSM_CNTR Register (Address = 18h) [reset = 0h]
      15. 8.6.15 DEVICE_RST Register (Address = 19h) [reset = 0h]
      16. 8.6.16 DEVICE_CONFIG (Address = 1Ah) [reset = 80h]
      17. 8.6.17 DEVICE_CONFIG2 (Address = 1Bh) [reset = 0h]
      18. 8.6.18 SWE_TIMER (Address = 1Ch) [reset = 30h]
      19. 8.6.19 LIN_CNTL (Address = 1Dh) [reset = 00h]
      20. 8.6.20 HSS_CNTL (Address = 1Eh) [reset = 0h]
      21. 8.6.21 PWM1_CNTL1 (Address = 1Fh) [reset = 0h]
      22. 8.6.22 PWM1_CNTL2 (Address = 20h) [reset = 0h]
      23. 8.6.23 PWM1_CNTL3 (Address = 21h) [reset = 00h]
      24. 8.6.24 PWM2_CNTL1 (Address = 22h) [reset = 0h]
      25. 8.6.25 PWM2_CNTL2 (Address = 23h) [reset = 0h]
      26. 8.6.26 PWM2_CNTL3 (Address = 24h) [reset = 0h]
      27. 8.6.27 TIMER1_CONFIG (Address = 25h) [reset = 00h]
      28. 8.6.28 TIMER2_CONFIG (Address = 26h) [reset = 00h]
      29. 8.6.29 RSRT_CNTR (Address = 28h) [reset = 40h]
      30. 8.6.30 nRST_CNTL (Address = 29h) [reset = 00h]
      31. 8.6.31 INT_GLOBAL Register (Address = 50h) [reset = A0h]
      32. 8.6.32 INT_1 Register (Address = 51h) [reset = 0h]
      33. 8.6.33 INT_2 Register (Address = 52h) [reset = 40h]
      34. 8.6.34 INT_3 Register (Address 53h) [reset = 0h]
      35. 8.6.35 INT_EN_1 Register (Address = 56h) [reset = B0h]
      36. 8.6.36 INT_EN_2 Register (Address = 57h) [reset = 37h]
      37. 8.6.37 INT_EN_3 Register (Address =58h) [reset = BCh]
      38. 8.6.38 INT_4 Register (Address = 5Ah) [reset = 0h]
      39. 8.6.39 INT_EN_4 Register (Address = 5Eh) [reset = CCh]
      40. 8.6.40 Reserved Registers
  9. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Device Brownout Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Normal Mode Application Note
        2. 9.2.1.2 Standby Mode Application Note
        3. 9.2.1.3 TXD Dominant State Timeout Application Note
      2. 9.2.2 Detailed Design Procedures
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 サポート・リソース
    4. 10.4 商標
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  11. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • RGY|20
サーマルパッド・メカニカル・データ
発注情報

8.6.17 DEVICE_CONFIG2 (Address = 1Bh) [reset = 0h]

DEVICE_CONFIG2 is shown in Figure 8-71 and described in Table 8-27

Return to Summary Table.

LIMP pin configuration and control.

Figure 8-71 DEVICE_CONFIG2 Register
76543210
LIMP_HSS_SELLIMP_HSS_CNTLLIMP_HSS_ONWAKE_WIDTH _MAX_DISRSVD
R/W-00bR/W-000bR/W-0bR/W-0bR-0b
Table 8-27 DEVICE_CONFIG2 Register Field Descriptions
BitFieldTypeResetDescription
7-6LIMP_HSS_SELR/W00bSelects LIMP pin function
00b = LIMP
01b = High side switch
10b = INH
11b = Reserved
5-3LIMP_HSS_CNTLR/W000bSelects the method of control for the LIMP pin when configured as a high side switch
000b = On/Off
001b = PWM1
010b = PWM2
011b = Timer1
100b = Timer2
101b - 111b = Reserved
2LIMP_HSS_ONR/W0bWhen LIMP is configured as HSS and control is On/Off this bit turns on or off the LIMP pin.
0b = Off
1b = On
1WAKE_WIDTH _MAX_DISR/W0bDisables the Max limit, tWK_PULSE_WIDTH_MAX detection when pulse is selected for WAKE pin wake up.
0b = Enabled
1b = Disabled
0RSVDR0bReserved