JAJSO44A June   2023  – September 2024 TMUX582F-SEP

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics (Global)
    6. 5.6 Single Supply: Electrical Characteristics
    7. 5.7 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1  On-Resistance
    2. 6.2  Off-Leakage Current
    3. 6.3  On-Leakage Current
    4. 6.4  Input and Output Leakage Current Under Overvoltage Fault
    5. 6.5  Break-Before-Make Delay
    6. 6.6  Enable Delay Time
    7. 6.7  Transition Time
    8. 6.8  Fault Response Time
    9. 6.9  Fault Recovery Time
    10. 6.10 Fault Flag Response Time
    11. 6.11 Fault Flag Recovery Time
    12. 6.12 Charge Injection
    13. 6.13 Off Isolation
    14. 6.14 Crosstalk
    15. 6.15 Bandwidth
    16. 6.16 THD + Noise
  8. 7 Truth Table
  9. 8 Detailed Description
    1. 8.1 Functional Block Diagram
    2. 8.2 Feature Description
      1. 8.2.1 Flat ON- Resistance
      2. 8.2.2 Protection Features
        1. 8.2.2.1 Powered-Off Protection
        2. 8.2.2.2 Fail-Safe Logic
        3. 8.2.2.3 Overvoltage Protection and Detection
        4. 8.2.2.4 Adjacent Channel Operation During Fault
        5. 8.2.2.5 ESD Protection
        6. 8.2.2.6 Latch-Up Immunity
        7. 8.2.2.7 EMC Protection
      3. 8.2.3 Overvoltage Fault Flags
      4. 8.2.4 Bidirectional and Rail-to-Rail Operation
      5. 8.2.5 1.8V Logic Compatible Inputs
      6. 8.2.6 Integrated Pull-Down Resistor on Logic Pins
    3. 8.3 Device Functional Modes
      1. 8.3.1 Normal Mode
      2. 8.3.2 Fault Mode
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 System Diagnostics – Telemetry
      2. 9.2.2 Design Requirements
      3. 9.2.3 Detailed Design Procedure
      4. 9.2.4 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 ドキュメントの更新通知を受け取る方法
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 静電気放電に関する注意事項
    6. 10.6 用語集
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • PW|20
サーマルパッド・メカニカル・データ
発注情報

8.2.4 Bidirectional and Rail-to-Rail Operation

The TMUX582F-SEP conducts equally well from source (Sx) to drain (D or Dx) or from drain (D or Dx) to source (Sx). Each signal path has very similar characteristics in both directions. It is important to note, however, that the overvoltage protection is implemented only on the source (Sx) side. The voltage on the drain is only allowed to swing between VFP and VFN and no overvoltage protection is available on the drain side.

The primary supplies (VDD and VSS) define the on-resistance profile of the switch channel, whereas the fault voltage supplies (VFP and VFN) define the signal range that can be passed through from source to drain of the device. It is good practice to use voltages on VFP and VFN that are lower than VDD and VSS to take advantage of the flat on-resistance region of the device for better input-to-output linearity. The flattest on-resistance region is roughly 3V below VDD. Once the signal is within 3V of VDD the on-resistance will exponentially increase and may impact desired signal transmission.