JAJSI28A October   2019  – August 2020 TPA3139D2

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics,
      1. 6.7.1 Bridge -Tied Load (BTL)
      2. 6.7.2 Paralleled Bridge -Tied Load (PBTL)
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Analog Gain
      2. 7.3.2  SD/ FAULT and MUTE Operation
      3. 7.3.3  PLIMIT
      4. 7.3.4  Spread Spectrum and De-Phase Control
      5. 7.3.5  GVDD Supply
      6. 7.3.6  DC Detect
      7. 7.3.7  PBTL Select
      8. 7.3.8  Short-Circuit Protection and Automatic Recovery Feature
      9. 7.3.9  Over-Temperature Protection (OTP)
      10. 7.3.10 Over-Voltage Protection (OVP)
      11. 7.3.11 Under-Voltage Protection (UVP)
    4. 7.4 Device Functional Modes
      1. 7.4.1 MODE_SEL = LOW: BD Modulation
      2. 7.4.2 MODE_SEL = HIGH: Low-Idle-Current 1SPW Modulation
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Design Requirements
        1. 8.2.1.1 PCB Material Recommendation
        2. 8.2.1.2 PVCC Capacitor Recommendation
        3. 8.2.1.3 Decoupling Capacitor Recommendations
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Ferrite Bead Filter Considerations
        2. 8.2.2.2 Efficiency: LC Filter Required with the Traditional Class-D Modulation Scheme
        3. 8.2.2.3 When to Use an Output Filter for EMI Suppression
        4. 8.2.2.4 Input Resistance
        5. 8.2.2.5 Input Capacitor, Ci
        6. 8.2.2.6 BSN and BSP Capacitors
        7. 8.2.2.7 Differential Inputs
        8. 8.2.2.8 Using Low-ESR Capacitors
      3. 8.2.3 Application Performance Curves
        1. 8.2.3.1 EN55013 Radiated Emissions Results
        2. 8.2.3.2 EN55022 Conducted Emissions Results
  9. 9 Power Supply Recommendations
    1. 9.1 Power Supply Decoupling, CS
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 Support Resources
    5. 11.5 Trademarks
    6. 11.6 静電気放電に関する注意事項
    7. 11.7 Glossary

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.3.2 SD/ FAULT and MUTE Operation

The TPA3139D2 device employs a shutdown mode of operation designed to reduce supply current (ICC) to the absolute minimum level during periods of nonuse for power conservation. The SD/ FAULT input pin should be held high (see Section 6 table for trip point) during normal operation when the amplifier is in use. Pulling SD/ FAULT low causes the outputs to mute and the amplifier to enter a low-current state. Never leave SD/ FAULT unconnected, because the amplifier operation would be unpredictable.

For the best power-off pop performance, place the amplifier in the shutdown or mute mode prior to removing the power supply voltage.

For some single ended input application case, suggest to mute the device first then release SD/ FAULT, then umute the output. This sequence power-up sequence with best pop performance.