JAJSKH0C April   2023  – February 2024 TPS274C65

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
    1.     7
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 SPI Timing Requirements
    8. 6.8 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Pin Diagrams
      2. 8.3.2 SPI Mode Operation
        1. 8.3.2.1 Diagnostic Bit Behavior
      3. 8.3.3 Programmable Current Limit
        1. 8.3.3.1 Inrush Current Handling
      4. 8.3.4 DO_EN Feature
      5. 8.3.5 Protection Mechanisms
        1. 8.3.5.1 Overcurrent Protection
        2. 8.3.5.2 Short Circuit Protection
          1. 8.3.5.2.1 VS During Short-to-Ground
        3. 8.3.5.3 Inductive-Load Switching-Off Clamp
        4. 8.3.5.4 Inductive Load Demagnetization
        5. 8.3.5.5 Thermal Shutdown
        6. 8.3.5.6 Undervoltage protection on VS
        7. 8.3.5.7 Undervoltage Lockout on Low Voltage Supply (VDD_UVLO)
        8. 8.3.5.8 Power-Up and Power-Down Behavior
        9. 8.3.5.9 Reverse Current Blocking
      6. 8.3.6 Diagnostic Mechanisms
        1. 8.3.6.1 Current Sense
          1. 8.3.6.1.1 RSNS Value
            1. 8.3.6.1.1.1 SNS Output Filter
        2. 8.3.6.2 Fault Indication
          1. 8.3.6.2.1 Current Limit Behavior
        3. 8.3.6.3 Short-to-Battery and Open-Load Detection
        4. 8.3.6.4 On-State Wire-Break Detection
        5. 8.3.6.5 Off State Wire-Break Detection
        6. 8.3.6.6 ADC
      7. 8.3.7 LED Driver
    4. 8.4 Device Functional Modes
      1. 8.4.1 OFF/POR
      2. 8.4.2 INIT
      3. 8.4.3 Active
    5. 8.5 TPS274C65BS Available Registers List
    6. 8.6 TPS274C65 Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 IEC 61000-4-5 Surge
        2. 9.2.2.2 Loss of GND
        3. 9.2.2.3 Paralleling Channels
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 ドキュメントの更新通知を受け取る方法
    2. 10.2 サポート・リソース
    3. 10.3 Trademarks
    4. 10.4 静電気放電に関する注意事項
    5. 10.5 用語集
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.3.5.5 Thermal Shutdown

The TPS274C65 includes a temperature sensor on the power FET and also within the controller portion of the device. There are two cases that the device will register a thermal shutdown fault:

  • TJ,FET > TABS
  • (TJ,FET – TJ,controller) > TREL

The first condition enables the device to register a long-term overtemperature event (caused by ambient temperature or too high DC current flow), while the second condition allows the device to quickly register transient heating that is causes in events like short-circuits.

After the fault is detected, the switch will turn off. If TJ,FET passes TABS, the fault is cleared when the switch temperature decreases by the hysteresis value, THYS. If instead the TREL threshold is exceeded, the fault is cleared after TRETRY passes.

Each channel will shut down independently in case of a thermal event, as each has it's own temperature sensor and fault reporting.