JAJSHQ7A July   2019  – September 2019 TPS3870-Q1

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      過電圧検出機能を内蔵
      2.      過電圧精度の標準的な分散
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
    1.     Pin Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 VDD
      2. 9.3.2 SENSE
      3. 9.3.3 RESET
      4. 9.3.4 Capacitor Time (CT)
      5. 9.3.5 Manual Reset (MR)
    4. 9.4 Device Functional Modes
      1. 9.4.1 Normal Operation (VDD > VDD(MIN))
      2. 9.4.2 Undervoltage Lockout (VPOR < VDD < UVLO)
      3. 9.4.3 Power-On Reset (VDD < VPOR)
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Voltage Threshold Accuracy
      2. 10.1.2 CT Reset Time Delay
        1. 10.1.2.1 Factory-Programmed Reset Delay Timing
        2. 10.1.2.2 Programmable Reset Delay-Timing
      3. 10.1.3 RESET Latch Mode
      4. 10.1.4 Adjustable Voltage Thresholds
      5. 10.1.5 Immunity to SENSE Pin Voltage Transients
        1. 10.1.5.1 Hysteresis
    2. 10.2 Typical Application
      1. 10.2.1 Design 1: RESET Latch Mode
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
        3. 10.2.1.3 Application Curves
  11. 11Power Supply Recommendations
    1. 11.1 Power Supply Guidelines
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13デバイスおよびドキュメントのサポート
    1. 13.1 デバイスの項目表記
    2. 13.2 ドキュメントのサポート
      1. 13.2.1 評価基板
    3. 13.3 ドキュメントの更新通知を受け取る方法
    4. 13.4 サポート・リソース
    5. 13.5 商標
    6. 13.6 静電気放電に関する注意事項
    7. 13.7 Glossary
  14. 14メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.3.3 RESET

In a typical TPS3870-Q1 application, the RESET output is connected to a reset or enable input of a processor [such as a digital signal processor (DSP), application-specific integrated circuit (ASIC), or other processor type] or the enable input of a voltage regulator [such as a DC-DC converter or low-dropout regulator (LDO)].

The TPS3870-Q1 has an open drain active low output that requires a pull-up resistor to hold these lines high to the required voltage logic. Connect the pull-up resistor to the proper voltage rail to enable the output to be connected to other devices at the correct interface voltage levels. To ensure proper voltage levels, give some consideration when choosing the pull-up resistor values. The pull-up resistor value is determined by VOL, output capacitive loading, and output leakage current. These values are specified in Specifications. The open drain output can be connected as a wired-OR logic with other open drain signals such as another TPS3870-Q1 RESET pin.

Table 2 describes the scenarios when the output (RESET) is either asserted low or high impedance.

TPS3870-Q1 Timing-Window.gifFigure 18. RESET output