JAJSCZ8B March   2017  – February 2018 TPS3890-Q1

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      代表的なアプリケーション回路
      2.      VITNの精度と温度との関係
  4. 4 改訂履歴
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 User-Configurable RESET Delay Time
      2. 8.3.2 Manual Reset (MR) Input
      3. 8.3.3 RESET Output
      4. 8.3.4 SENSE Input
        1. 8.3.4.1 Immunity to SENSE Pin Voltage Transients
    4. 8.4 Device Functional Modes
      1. 8.4.1 Normal Operation (VDD > VDD(min))
      2. 8.4.2 Above Power-On-Reset But Less Than VDD(min) (VPOR < VDD < VDD(min))
      3. 8.4.3 Below Power-On-Reset (VDD < VPOR)
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curve
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 デバイス・サポート
      1. 12.1.1 デバイスの項目表記
    2. 12.2 ドキュメントのサポート
      1. 12.2.1 関連資料
    3. 12.3 ドキュメントの更新通知を受け取る方法
    4. 12.4 コミュニティ・リソース
    5. 12.5 商標
    6. 12.6 静電気放電に関する注意事項
    7. 12.7 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6 Pin Configuration and Functions

DSE Package
6-Pin WSON
Top View

Pin Functions

PIN I/O DESCRIPTION
NO. NAME
1 SENSE I This pin is connected to the voltage to be monitored. When the voltage on SENSE falls below the negative threshold voltage VITN, RESET goes low (asserts). When the voltage on SENSE rises above the positive threshold voltage VITP, RESET goes high (deasserts).
2 GND — Ground
3 MR I Driving the manual reset pin (MR) low causes RESET to go low (assert).
4 VDD I Supply voltage pin. Good analog design practice is to place a 0.1-µF ceramic capacitor close to this pin.
5 CT — The CT pin offers a user-adjustable delay time. Connecting this pin to a ground-referenced capacitor sets the RESET delay time to deassert. tPD(r) (sec) = CCT (µF) × 1.07 + 25 µs (nom).
6 RESET O RESET is an open-drain output that is driven to a low-impedance state when either the MR pin is driven to a logic low or the monitored voltage on the SENSE pin is lower than the negative threshold voltage (VITN). RESET remains low (asserted) for the delay time period after both MR is set to a logic high and the SENSE input is above VITP. A pullup resistor from 10 kΩ to 1 MΩ should be used on this pin.