SLVS400D August   2001  – January 2015 TPS54611 , TPS54612 , TPS54613 , TPS54614 , TPS54615 , TPS54616

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 Recommended Operating Conditions
    3. 6.3 Thermal Information
    4. 6.4 Dissipation Ratings
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Undervoltage Lock Out (UVLO)
      2. 7.3.2  Slow-Start and Enable (SS/ENA)
      3. 7.3.3  VBIAS Regulator
      4. 7.3.4  Voltage Reference
      5. 7.3.5  Oscillator and PWM Ramp
      6. 7.3.6  Error Amplifier
      7. 7.3.7  PWM Control
      8. 7.3.8  Dead-Time Control and MOSFET Drivers
      9. 7.3.9  Overcurrent Protection
      10. 7.3.10 Thermal Shutdown
      11. 7.3.11 Powergood (PWRGD)
    4. 7.4 Device Functional Modes
      1. 7.4.1 Continuous Conduction Mode
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Component Selection
        2. 8.2.2.2 Input Filter
        3. 8.2.2.3 Feedback Circuit
        4. 8.2.2.4 Operating Frequency
        5. 8.2.2.5 Output Filter
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
    3. 10.3 Thermal Considerations
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Related DC - DC Products
    2. 11.2 Related Links
    3. 11.3 Trademarks
    4. 11.4 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6 Specifications

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
VI Input voltage VIN, SS/ENA, FSEL −0.3 7 V
RT −0.3 6 V
VSENSE −0.3 4 V
BOOT −0.3 17 V
VO Output voltage VBIAS, PWRGD −0.3 7 V
PH −0.6 10 V
IO Source current PH Internally Limited V
VBIAS 6 mA
IS Sink current PH 12 A
SS/ENA, PWRGD 10 mA
Voltage differential AGND to PGND –0.3 0.3 V
Continuous power dissipation See
TJ Operating virtual junction temperature –40 125 °C
Tstg Storage temperature −65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

6.2 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN NOM MAX UNIT
Controller Input Voltage, VIN 3 6 V
Junction Temperature, TJ –40 125 °C

6.3 Thermal Information(1)

THERMAL METRIC(2) TPS5461x UNIT
PWP (28 PINS)
RθJA Junction-to-ambient thermal resistance, with solder 18.2 °C/W
Junction-to-ambient thermal resistance, without solder 40.5
(1) Test Board Conditions:
  1. 3 inches × 3 inches, 4 layers, thickness: 0.062 inch
  2. 1.5 oz. copper traces located on the top of the PCB
  3. 1.5 oz. copper ground plane on the bottom of the PCB
  4. 0.5 oz. copper ground planes on the 2 internal layers
  5. 12 thermal vias. See Figure 19 for more information.
(2) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.

6.4 Dissipation Ratings(1)(2)

TA = 25°C
POWER RATING		 TA = 70 °C
POWER RATING		 TA = 85 °C
POWER RATING 		UNIT
28 Pin PWP with Solder 5.49 (3) 3.02 2.20 W
28 Pin PWP without Solder 2.48 1.36 0.99 W
(1) For more information on the PWP package, refer to TI technical brief, SLMA002
(2) Test Board Conditions:
  1. 3 inches × 3 inches, 4 layers, thickness: 0.062 inch
  2. 1.5 oz. copper traces located on the top of the PCB
  3. 1.5 oz. copper ground plane on the bottom of the PCB
  4. 0.5 oz. copper ground planes on the 2 internal layers
  5. 12 thermal vias. See Figure 19 for more information.
(3) Maximum power dissipation may be limited by over-current protection

6.5 Electrical Characteristics

TJ = –40°C to 125°C, VI = 3 V to 6 V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY VOLTAGE, VIN
VIN Input voltage range 3.0 6.0 V
I(Q) Quiescent current fs = 350 kHz, FSEL ≤ 0.8 V, RT open, phase pin open 6.2 9.6 mA
fs = 550 kHz, FSEL ≤ 2.5 V, RT open, phase pin open 8.4 12.8
Shutdown, SS/ENA = 0 V 1 1.4
UNDERVOLTAGE LOCK OUT
UVLO Start threshold voltage 2.95 3.0 V
Stop threshold voltage 2.70 2.80 V
Hysteresis voltage 0.14 0.16 V
Rising and falling edge deglitch(3) 2.5 µs
BIAS VOLTAGE
VBIAS Output voltage I(VBIAS) = 0 2.70 2.80 2.90 V
Output current(1) 100 µA
OUTPUT VOLTAGE
VO Output voltage TPS54611 TJ = 25°C, VIN = 5 V 0.9 V
3 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40°C ≤ TJ ≤ 125°C –2.0% 2.0%
TPS54612 TJ = 25°C, VIN = 5 V 1.2 V
3 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40°C ≤ TJ ≤ 125°C –2.0% 2.0%
TPS54613 TJ = 25°C, VIN = 5 V 1.5 V
3 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40°C ≤ TJ ≤ 125°C –2.0% 2.0%
TPS54614 TJ = 25°C, VIN = 5 V 1.8 V
3 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40°C ≤ TJ ≤ 125°C –3.0% 3.0%
TPS54615 TJ = 25°C, VIN = 5 V 2.5 V
3 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40° ≤ TJ ≤ 125°C –3.0% 3.0%
TPS54616 TJ = 25°C, VIN = 5 V 3.3 V
4 V ≤ VIN ≤ 6 V, 0 ≤ IL ≤ 6 A, −40° ≤ TJ ≤ 125°C −3.0% 3.0%
REGULATION
Line regulation(3)(2) IL = 3 A, 350 ≤ fs ≤ 550 kHz, TJ = 85°C 0.088 %/V
Load regulation(3)(2) IL = 0 A to 6 A, 350 ≤ fs ≤ 550 kHz, TJ = 85°C 0.0917 %/A
OSCILLATOR
Internally set – free running frequency FSEL ≤ 0.8 V, RT open 280 350 420 kHz
FSEL ≥ 2.5 V, RT open 440 550 660
Externally set – free running frequency range RT = 180 kΩ (1% resistor to AGND)(3) 252 280 308 kHz
RT = 100 kΩ (1% resistor to AGND) 460 500 540
RT = 68 kΩ (1% resistor to AGND)(3) 663 700 762
FSEL High level threshold 2.5 V
Low level threshold 0.8 V
Ramp valley(3) 0.75 V
Ramp amplitude (peak-to-peak)(3) 1 V
Minimum controllable on time(3) 200 ns
Maximum duty cycle(3) 90%
ERROR AMPLIFIER
Error amplifier open loop voltage gain(3) 26 dB
Error amplifier unity gain bandwidth(3) 3 5 MHz
Error amplifier common mode input voltage range Powered by internal LDO(3) 0 VBIAS V
PWM COMPARATOR
PWM comparator propagation delay time, PWM comparator input to PH pin (excluding deadtime) 10-mV overdrive(3) 70 85 ns
SLOW-START/ENABLE
Enable threshold voltage, SS/ENA 0.82 1.20 1.40 V
Enable hysteresis voltage, SS/ENA(3) 0.03 V
Falling edge deglitch, SS/ENA(3) 2.5 µs
Internal slow-start time(3) TPS54611 2.6 3.3 4.1 ms
TPS54612 3.5 4.5 5.4
TPS54613 4.4 5.6 6.7
TPS54614 2.6 3.3 4.1
TPS54615 3.6 4.7 5.6
TPS54616 4.7 6.1 7.6
Charge current, SS/ENA SS/ENA = 0V 3 5 8 µA
Discharge current, SS/ENA SS/ENA = 0.2 V, VI = 2.7 V 1.5 2.3 4.0 mA
POWERGOOD
Powergood threshold voltage VSENSE falling 90 %VO
Powergood hysteresis voltage See (3) 3 %VO
Powergood falling edge deglitch See (3) 35 µs
Output saturation voltage, PWRGD I(sink) = 2.5 mA 0.18 0.3 V
Leakage current, PWRGD VI = 5.5 V 1 µA
CURRENT LIMIT
Current limit VI = 3 V(3) 7.2 10 A
VI = 6 V(3) 10 12
Current limit leading edge blanking time(3) 100 ns
Current limit total response time(3) 200 ns
THERMAL SHUTDOWN
Thermal shutdown trip point(3) 135 150 165 °C
Thermal shutdown hysteresis(3) 10
OUTPUT POWER MOSFETS
rDS(on) Power MOSFET switches IO = 3 A, VI = 6 V(4) 26 47 mΩ
IO = 3 A, VI = 3 V(4) 36 65
(1) Static resistive loads only
(2) Tested using circuit in Figure 10.
(3) Specified by design
(4) Matched MOSFETs, low-side rDS(on) production tested, high-side rDS(on) specified by design.

6.6 Typical Characteristics

Graph_01_SLVS400C.gif
Figure 1. Drain-source On-state Resistance vs Junction Temperature
Graph_03_SLVS400C.gif
Figure 3. Internally Set Oscillator Frequency vs Junction Temperature 3
Graph_05_SLVS400C.gif
Figure 5. Voltage Reference vs Junction Temperature
Graph_07_SLVS400C.gif
Figure 7. Error Amplifier Open Loop Response
Graph_09_SLVS400C.gif
Figure 9. Device Power Losses vs Load Current
Graph_02_SLVS400C.gif
Figure 2. Drain-source On-state Resistance vs Junction Temperature 2
Graph_04_SLVS400C.gif
Figure 4. Externally Set Oscillator Frequency vs Junction Temperature 4
Graph_06_SLVS400C.gif
Tested using TPS54611
Figure 6. Output Voltage Regulation vs Input Voltage
Graph_08_SLVS400C.gif
Tested using TPS54611
Figure 8. Internal Slow-Start Time vs Junction Temperature