JAJSGE5C March   2019  – August 2019 TPS568230

PRODUCTION DATA.  

  1. 特長
  2. アプリケーション
  3. 概要
    1.     Device Images
      1.      代表的なアプリケーション
      2.      効率と出力電流との関係、 ECO-mode
  4. 改訂履歴
  5. 概要(続き)
  6. Pin Configuration and Functions
    1.     Pin Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 PWM Operation and D-CAP3 Control
      2. 8.3.2 Soft Start
      3. 8.3.3 Large Duty Operation
      4. 8.3.4 Power Good
      5. 8.3.5 Over Current Protection and Undervoltage Protection
      6. 8.3.6 Over Voltage Protection
      7. 8.3.7 UVLO Protection
      8. 8.3.8 Output Voltage Discharge
      9. 8.3.9 Thermal Shutdown
    4. 8.4 Device Functional Modes
      1. 8.4.1 Light Load Operation
      2. 8.4.2 Advanced Eco-mode Control
      3. 8.4.3 Out of Audio Mode
      4. 8.4.4 Force CCM Mode
      5. 8.4.5 Mode Selection
      6. 8.4.6 Standby Operation
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 External Component Selection
          1. 9.2.2.1.1 Output Voltage Set Point
          2. 9.2.2.1.2 Inductor Selection
          3. 9.2.2.1.3 Output Capacitor Selection
          4. 9.2.2.1.4 Input Capacitor Selection
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 デバイス・サポート
      1. 12.1.1 デベロッパー・ネットワークの製品に関する免責事項
    2. 12.2 ドキュメントの更新通知を受け取る方法
    3. 12.3 コミュニティ・リソース
    4. 12.4 商標
    5. 12.5 静電気放電に関する注意事項
    6. 12.6 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Pin Configuration and Functions

RJE Package
20-Pin VQFN
Top View
TPS568230 pinout-01-slvse32.gif

Pin Functions

PIN I/O DESCRIPTION
NAME NO.
BST 1 I Supply input for the gate drive voltage of the high-side MOSFET. Connect the bootstrap capacitor between BST and SW, 0.1uF is recommended.
VIN 2,3,4,5 P Input voltage supply pin for the control circuitry. Connect the input decoupling capacitors between VIN and GND.
SW 6,19,20 O Switch node terminal. Connect the output inductor to this pin.
GND 7,8,18,Pad G Power GND terminal for the controller circuit and the internal circuitry.
PGOOD 9 O Open drain power good indicator. It is asserted low if output voltage is out of PGOOD threshold, over voltage or if the device is under thermal shutdown, EN shutdown or during soft start.
SS 11 I Soft-start time selection pin. Connecting an external capacitor sets the soft-start time and if no external capacitor is connected, the soft-start time is about 1.3ms.
NC 10,16 Not connect. Can be connected to GND plane for better thermal achieved.
EN 12 I Enable pin of buck converter. EN pin is a digital input pin, decides turn on or off buck converter. Internal pull down current to disable converter if leave this pin open.
AGND 13 G Ground of internal analog circuitry. Connect AGND to GND plane with a short trace.
FB 14 I Converter feedback input. Connect to the center tap of the resistor divider between output voltage and AGND.
MODE 15 I Switching frequency and light load operation mode selection pin. Connect this pin to a resistor divider from VCC and AGND, the different MODE options are shown in Table 1
VCC 17 O 5.0-V internal VCC LDO output. This pin supplies voltage to the internal circuitry and gate driver. Bypass this pin with a 1-μF capacitor.