SLVSAF6A June   2011  – January 2016 TPS65835

PRODUCTION DATA.  

  1. 1 Device Overview
    1. 1.1 Features
    2. 1.2 Applications
    3. 1.3 Description
    4. 1.4 Block Diagram
  2. 2 Revision History
  3. 3 Terminal Configuration and Functions
    1. 3.1 Pin Diagram
    2. 3.2 Pin Functions
  4. 4 Specifications
    1. 4.1 Absolute Maximum Ratings
    2. 4.2 ESD Ratings
    3. 4.3 Power-On Hours (POH)
    4. 4.4 Recommended Operating Conditions
    5. 4.5 Thermal Information
    6. 4.6 Electrical Characteristics
    7. 4.7 Quiescent Current
    8. 4.8 Typical Characteristics
  5. 5 Detailed Description
    1. 5.1 Overview
    2. 5.2 Functional Block Diagram
    3. 5.3 Feature Description
      1. 5.3.1 System Operation
        1. 5.3.1.1 System Power Up
        2. 5.3.1.2 System Operation Using Push Button Switch
        3. 5.3.1.3 System Operation Using Slider Switch
      2. 5.3.2 Linear Charger Operation
        1. 5.3.2.1 Battery and TS Detection
        2. 5.3.2.2 Battery Charging
          1. 5.3.2.2.1 Pre-charge
          2. 5.3.2.2.2 Charge Termination
          3. 5.3.2.2.3 Recharge
          4. 5.3.2.2.4 Charge Timers
        3. 5.3.2.3 Charger Status (nCHG_STAT Pin)
      3. 5.3.3 LDO Operation
        1. 5.3.3.1 LDO Internal Current Limit
      4. 5.3.4 Boost Converter Operation
        1. 5.3.4.1 Boost Thermal Shutdown
        2. 5.3.4.2 Boost Load Disconnect
      5. 5.3.5 Full H-Bridge Analog Switches
        1. 5.3.5.1 H-Bridge Switch Control
      6. 5.3.6 Power Management Core Control
        1. 5.3.6.1 SLEEP / Power Control Pin Function
        2. 5.3.6.2 COMP Pin Functionality
        3. 5.3.6.3 SW_SEL Pin Functionality
        4. 5.3.6.4 SWITCH Pin
        5. 5.3.6.5 Slider Switch Behavior
        6. 5.3.6.6 Push-Button Switch Behavior
    4. 5.4 Device Functional Modes
      1. 5.4.1 SLEEP State
      2. 5.4.2 NORMAL Operating Mode
    5. 5.5 MSP430 CORE
      1. 5.5.1 MSP430 Electrical Characteristics
        1. 5.5.1.1  MSP430 Recommended Operating Conditions
        2. 5.5.1.2  Active Mode Supply Current Into VCC Excluding External Current
        3. 5.5.1.3  Typical Characteristics, Active Mode Supply Current (Into VCC)
        4. 5.5.1.4  Low-Power Mode Supply Currents (Into VCC) Excluding External Current
        5. 5.5.1.5  Typical Characteristics, Low-Power Mode Supply Currents
        6. 5.5.1.6  Schmitt-Trigger Inputs, Ports Px
        7. 5.5.1.7  Leakage Current, Ports Px
        8. 5.5.1.8  Outputs, Ports Px
        9. 5.5.1.9  Output Frequency, Ports Px
        10. 5.5.1.10 Typical Characteristics, Outputs
        11. 5.5.1.11 Pin-Oscillator Frequency - Ports Px
        12. 5.5.1.12 Typical Characteristics, Pin-Oscillator Frequency
        13. 5.5.1.13 POR/Brownout Reset (BOR)
        14. 5.5.1.14 Typical Characteristics, POR/Brownout Reset (BOR)
        15. 5.5.1.15 DCO Frequency
        16. 5.5.1.16 Calibrated DCO Frequencies, Tolerance
        17. 5.5.1.17 Wake-Up From Lower-Power Modes (LPM3/4)
        18. 5.5.1.18 Typical Characteristics, DCO Clock Wake-Up Time From LPM3/4
        19. 5.5.1.19 Crystal Oscillator, XT1, Low-Frequency Mode
        20. 5.5.1.20 Internal Very-Low-Power Low-Frequency Oscillator (VLO)
        21. 5.5.1.21 Timer_A
        22. 5.5.1.22 USCI (UART Mode)
        23. 5.5.1.23 USCI (SPI Master Mode)
        24. 5.5.1.24 USCI (SPI Slave Mode)
        25. 5.5.1.25 USCI (I2C Mode)
        26. 5.5.1.26 Comparator_A+
        27. 5.5.1.27 Typical Characteristics - Comparator_A+
        28. 5.5.1.28 10-Bit ADC, Power Supply and Input Range Conditions
        29. 5.5.1.29 10-Bit ADC, Built-In Voltage Reference
        30. 5.5.1.30 10-Bit ADC, External Reference
        31. 5.5.1.31 10-Bit ADC, Timing Parameters
        32. 5.5.1.32 10-Bit ADC, Linearity Parameters
        33. 5.5.1.33 10-Bit ADC, Temperature Sensor and Built-In VMID
        34. 5.5.1.34 Flash Memory
        35. 5.5.1.35 RAM
        36. 5.5.1.36 JTAG and Spy-Bi-Wire Interface
        37. 5.5.1.37 JTAG Fuse
      2. 5.5.2 MSP430 Core Operation
        1. 5.5.2.1 Description
        2. 5.5.2.2 Accessible MSP430 Pins
        3. 5.5.2.3 MSP430 Port Functions and Programming Options
        4. 5.5.2.4 Operating Modes
        5. 5.5.2.5 MSP430x2xx User's Guide
  6. 6 Application and Implementation
    1. 6.1 Application Information
    2. 6.2 Typical Application
      1. 6.2.1 Active Shutter 3D Glasses
        1. 6.2.1.1 Design Requirements
        2. 6.2.1.2 Detailed Design Procedure
          1. 6.2.1.2.1 Boost Converter Application Information
            1. 6.2.1.2.1.1 Setting Boost Output Voltage
            2. 6.2.1.2.1.2 Boost Inductor Selection
            3. 6.2.1.2.1.3 Boost Capacitor Selection
          2. 6.2.1.2.2 Bypassing Default Push-Button SWITCH Functionality
          3. 6.2.1.2.3 MSP430 Programming
            1. 6.2.1.2.3.1 Code To Setup Power Functions
        3. 6.2.1.3 Application Curves
  7. 7  Power Supply Recommendations
  8. 8 Layout
    1. 8.1 Layout Guidelines
    2. 8.2 Layout Example
  9. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
    2. 9.2 Community Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  10. 10Mechanical, Packaging, and Orderable Information
    1. 10.1 Packaging Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality.

6.1 Application Information

This PMIC is designed specifically for active shutter 3D glasses.

6.2 Typical Application

6.2.1 Active Shutter 3D Glasses

TPS65835 TPS65835_App_Schematic.gif Figure 6-1 TPS65835 Applications Schematic

6.2.1.1 Design Requirements

The design parameters are located in Table 6-1.

Table 6-1 Design Parameters

PARAMETER EXAMPLE
Input Voltage, VIN 3.7 to 6.4 V
Input Voltage, Vbat BAT 2.5 to 6.4 V
Output Voltage, LDO VLDO 2.2 (default) or 3.0 V
Output Voltage Boost, BST_OUT 8 to 16 V, 10 V default
Charge Current Ichg=Kiset/Riset 5 to 100 mA, 70 mA default
Input Voltage Low VIL
(BST_EN, CHG_EN, SW_SEL, VLDO, HBRx, HBLx) 		0.4 V
Input Voltage High VIH
(BST_EN, CHG_EN, SW_SEL, VLDO, HBRx, HBLx) 		1.2 V

6.2.1.2 Detailed Design Procedure

6.2.1.2.1 Boost Converter Application Information

6.2.1.2.1.1 Setting Boost Output Voltage

To set the boost converter output voltage of this device, two external resistors that form a feedback network are required. The values recommended below (in Table 6-2) are given for a desired quiescent current of 5 µA when the boost is enabled and switching. See Figure 6-2 for the detail of the applications schematic that shows the boost feedback network and the resistor names used in the table below.

TPS65835 TPS65x3x_Boost_FB_Apps.gif Figure 6-2 Boost Feedback Network Schematic

Table 6-2 Recommended RFB1 and RFB2 Values (for IQ(FB) = 5 µA)

TARGETED VBST_OUT RFB1(1) RFB2(1)
8 V 1.3 MΩ 240 kΩ
10 V 1.8 MΩ 240 kΩ
12 V 2.2 MΩ 240 kΩ
14 V 2.4 MΩ 240 kΩ
16 V 3.0 MΩ 240 kΩ
(1) Resistance values given in closest standard value (5% tolerance, E24 grouping).

These resistance values can also be calculated using the following information. To start, it is helpful to target a quiescent current through the boost feedback network while the device is operating (IQ(FB)). When the boost output voltage and this targeted quiescent current is known, the total feedback network resistance can be found.

The value for RFB2 can be found by using the boost feedback pin voltage (VFB = 1.2 V, see Section 4.6) and IQ(FB) using Equation 1:

Equation 1. RFB1 + RFB2 = VBST_OUT / IQ(FB)
Equation 2. RFB2 = (1.2 V) / IQ(FB)

To find RFB1, simply subtract the RFB2 from RFB(TOT) as shown in Equation 3.

Equation 3. RFB1 = RFB(TOT) - RFB2

6.2.1.2.1.2 Boost Inductor Selection

The selection of the boost inductor and output capacitor is very important to the performance of the boost converter. The boost has been designed for optimized operation when a 10 µH inductor is used. Smaller inductors, down to 4.7 µH, may be used but there will be a slight loss in overall operating efficiency. A few inductors that have been tested and found to give good performance can be found in the following list.

Recommended 10-µH inductors:

  • TDK VLS201612ET-100M (10 µH, IMAX = 0.53 A, RDC = 0.85 Ω)
  • Taiyo Yuden CBC2016B100M (10 µH, IMAX = 0.41 A, RDC = 0.82 Ω)

6.2.1.2.1.3 Boost Capacitor Selection

The recommended minimum value for the capacitor on the boost output, BST_OUT pin, is 4.7 µF. Values that are larger can be used with the measurable impact being a slight reduction in the boost converter output voltage ripple while values smaller than this will result in an increased boost output voltage ripple. Note that the voltage rating of the capacitor should be sized for the maximum expected voltage at the BST_OUT pin.

6.2.1.2.2 Bypassing Default Push-Button SWITCH Functionality

If the SWITCH pin functionality is not required to power on and off the device because of different system requirements (SWITCH timing requirements of system will be controlled by the internal MSP430), then the feature can be bypassed. The following diagram shows the connections required for this configuration.

TPS65835 TPS65835_Apps_No_SWITCH.gif Figure 6-3 Bypassing Default TPS65835 Push Button SWITCH Timing

In a system where a different push-button SWITCH off timing is required, the SLEEP pin is used to control the power off of the device. After system power up, the MCU must force the SLEEP pin to a high state (VSLEEP > VIH(PMIC)). Once the SWITCH push-button is pressed to shut the system down, a timer in the MCU should be active and counting the desired tOFF time of the device. Once this tOFF time is detected, the MCU can assert the SLEEP signal to a logic low level (VSLEEP < VIL(PMIC)). It is on the falling edge of the SLEEP signal where the system will be powered off (see Figure 6-4).

TPS65835 TPS65x35_SWITCH_power_off_SLEEP.gif Figure 6-4 SWITCH Press and SLEEP Signal to Control System Power Off

6.2.1.2.3 MSP430 Programming

In order to program the integrated MSP430 in the TPS65835 device, ensure that the programming environment supports the TPS65835 device.

6.2.1.2.3.1 Code To Setup Power Functions

This section will detail a basic code to control the MSP430 in the TPS65835 and how to configure the power functions and control the power die. Please reference Table 5-9 for the details on configuring the MSP430 pins. Note that "//" is a comment and this code was written using Code Composer Studio in C.


// SETUP H-BRIDGE PINS P2DIR |= (BIT5 + BIT4 + BIT3 + BIT0); // Set PxDIR to 1 for outputs P2REN |= (BIT5 + BIT4 + BIT3 + BIT0); // Enable pull-up/pull-down resistors on outputs // SETUP SLEEP, CHG_EN, AND BST_EN P3DIR |= (BIT2 + BIT1 + BIT0); // Set PxDIR to 1 for outputs P3REN |= (BIT2 + BIT1 + BIT0); // Enable pull-up/pull-down resistors on outputs

The previous code setup the power pins for outputs, now they must be controlled with MSP430 code. Refer to the following code to perform initial setup and to control the power functions (SLEEP, CHG_EN, and BST_EN):


P3OUT &= ~BIT0; // Set SLEEP mode signal low; SLEEP Function is disabled // P3OUT |= BIT0; // Set SLEEP mode signal high (sleep control via MSP430) // P3OUT &= ~BIT1; // Set CHG_EN signal low (disable charger) P3OUT |= BIT1; // Set CHG_EN signal high (enable charger) // P3OUT &= ~BIT2; // Set BST_EN low (disable boost) P3OUT |= BIT2; // Set BST_EN high (enable boost)

The H-Bridge pins can be controlled in a similar manner (see Section 5.3.5.1). The following code is only meant to cover each H-Bridge mode of operation and the appropriate code needed to put it in that state:


// BOTH SIDES IN OPEN STATE P2OUT &= ~(BIT3 + BIT0); // HBL2 = 0, HBL1 = 0 P2OUT &= ~(BIT5 + BIT4); // HBR2 = 0, HBR1 = 0 // BOTH SIDES IN GROUNDED STATE P2OUT |= BIT3 + BIT0; // HBL2 = 1, HBL1 = 1 P2OUT |= BIT5 + BIT4; // HBR2 = 1, HBR1 = 1 // LEFT SIDE IN CHARGE+ STATE P2OUT &= ~BIT3; P2OUT |= BIT0; // HBL2 = 0, HBL1 = 1 // LEFT SIDE IN CHARGE- STATE P2OUT |= BIT3; P2OUT &= ~BIT0; // HBL2 = 1, HBL1 = 0 // RIGHT SIDE IN CHARGE+ STATE P2OUT &= ~BIT5; P2OUT |= BIT4; // HBR2 = 0, HBR1 = 1 // RIGHT SIDE IN CHARGE- STATE P2OUT |= BIT5; P2OUT &= ~BIT4; // HBR2 = 1, HBR1 = 0

6.2.1.3 Application Curves

TPS65835 boost_ripp_lvu418.gif
Vbat = –3.2 V 1-mA Load on Boost
Figure 6-5 Boost Output Ripple
TPS65835 switchnode_lvu418.gif
Vbat = 3.6 V No Load 0.5 µs/div
Figure 6-6 Switchnode