JAJSSZ7 February   2024 TUSB211A-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Switching Characteristics
    7. 5.7 Timing Requirements
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 High-Speed EQ
    4. 6.4 Device Functional Modes
      1. 6.4.1 Low-Speed (LS) Mode
      2. 6.4.2 Full-Speed (FS) Mode
      3. 6.4.3 High-Speed (HS) Mode
      4. 6.4.4 High-Speed Downstream Port Electrical Compliance Test Mode
      5. 6.4.5 Shutdown Mode
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Test Procedure to Construct USB High-Speed Eye Diagram
          1. 7.2.2.1.1 For a Host Side Application
          2. 7.2.2.1.2 For a Device Side Application
      3. 7.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 ドキュメントの更新通知を受け取る方法
    2. 8.2 サポート・リソース
    3. 8.3 Trademarks
    4. 8.4 静電気放電に関する注意事項
    5. 8.5 用語集
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • RWB|12
サーマルパッド・メカニカル・データ
発注情報
7.2.2.1.2 For a Device Side Application
  1. Configure the TUSB211A-Q1 to the desired EQ setting.
  2. Power on (or toggle the RSTN pin if already powered on) the TUSB211A-Q1.
  3. Connect a USB host, the USB-IF device-side test fixture, and USB device to the TUSB211A-Q1. Ensure that the USB-IF device test fixture is configured to the ‘INIT’ position.
  4. Allow the host to enumerate the device.
  5. Enable the device to transmit USB TEST_PACKET.
  6. Using SMA cables, connect the oscilloscope to the USB-IF device-side test fixture and ensure that the device-side test fixture is configured to the ‘TEST’ position.
  7. Execute the oscilloscope USB compliance software.
  8. Repeat the above steps to re-test TUSB211A-Q1 with a different EQ setting (must reset to change).