JAJSHT2C august   2019  – december 2020 UCC28740-Q1

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Revision History
  7. 6 Revision History
  8. 7 Pin Configuration and Functions
    1. 7.1 Pin Functions
  9. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Switching Characteristics
    7. 8.7 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Detailed Pin Description
      2. 9.3.2 Valley-Switching and Valley-Skipping
      3. 9.3.3 Startup Operation
      4. 9.3.4 Fault Protection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Secondary-Side Optically Coupled Constant-Voltage (CV) Regulation
      2. 9.4.2 Primary-Side Constant-Current (CC) Regulation
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 High Voltage Applications
    3. 10.3 Typical Application
      1. 10.3.1 Design Requirements
      2. 10.3.2 Detailed Design Procedure
        1. 10.3.2.1  Custom Design With WEBENCH® Tools
        2. 10.3.2.2  Standby Power Estimate and No-Load Switching Frequency
        3. 10.3.2.3  Input Bulk Capacitance and Minimum Bulk Voltage
        4. 10.3.2.4  38
        5. 10.3.2.5  Transformer Turns-Ratio, Inductance, Primary Peak Current
        6. 10.3.2.6  Transformer Parameter Verification
        7. 10.3.2.7  VS Resistor Divider, Line Compensation
        8. 10.3.2.8  Output Capacitance
        9. 10.3.2.9  VDD Capacitance, CVDD
        10. 10.3.2.10 Feedback Network Biasing
      3. 10.3.3 Application Curves
  12. 11Power Supply Recommendations
  13. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 VDD Pin
      2. 12.1.2 VS Pin
      3. 12.1.3 FB Pin
      4. 12.1.4 GND Pin
      5. 12.1.5 CS Pin
      6. 12.1.6 DRV Pin
      7. 12.1.7 HV Pin
    2. 12.2 Layout Example
  14. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Development Support
        1. 13.1.1.1 Custom Design With WEBENCH® Tools
      2. 13.1.2 Device Nomenclature
        1. 13.1.2.1  Capacitance Terms in Farads
        2. 13.1.2.2  Duty Cycle Terms
        3. 13.1.2.3  Frequency Terms in Hertz
        4. 13.1.2.4  Current Terms in Amperes
        5. 13.1.2.5  Current and Voltage Scaling Terms
        6. 13.1.2.6  Transformer Terms
        7. 13.1.2.7  Power Terms in Watts
        8. 13.1.2.8  Resistance Terms in Ohms
        9. 13.1.2.9  Timing Terms in Seconds
        10. 13.1.2.10 Voltage Terms in Volts
        11. 13.1.2.11 AC Voltage Terms in VRMS
        12. 13.1.2.12 Efficiency Terms
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 Receiving Notification of Documentation Updates
    4. 13.4 Community Resources
    5. 13.5 Trademarks
  15.   Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

12.1.5 CS Pin

A small filter capacitor may be placed on CS to GND, with short traces, to filter any ringing that may be present at light load conditions when driving MOSFETs with large gate capacitance. This capacitor may not be required in all designs; however, it is wise to put a place holder for it in your designs. The current sense resistor should be returned to the ground terminal of the input bulk capacitor to minimize the loop area containing the input capacitor, the transformer, the MOSFET, and the current sense resistor.