JAJSCF6G July   2016  – December  2019 TPS2660

PRODUCTION DATA.  

1. 1 特長
2. 2 アプリケーション
   1.     概略回路図
3. 3 概要
   1.     -60V電源における入力逆極性保護
4. 4 改訂履歴
5. 5 概要（続き）
6. 6 Device Comparison Table
7. 7 Pin Configuration and Functions
   1.     Pin Functions
8. 8 Specifications
   1. 8.1 Absolute Maximum Ratings
   2. 8.2 ESD Ratings
   3. 8.3 Recommended Operating Conditions
   4. 8.4 Thermal Information
   5. 8.5 Electrical Characteristics
   6. 8.6 Timing Requirements
   7. 8.7 Typical Characteristics
9. 9 Parameter Measurement Information
10. 10Detailed Description
    1. 10.1 Overview
    2. 10.2 Functional Block Diagram
    3. 10.3 Feature Description
       1. 10.3.1 Undervoltage Lockout (UVLO)
       2. 10.3.2 Overvoltage Protection (OVP)
       3. 10.3.3 Reverse Input Supply Protection
       4. 10.3.4 Hot Plug-In and In-Rush Current Control
       5. 10.3.5 Overload and Short Circuit Protection
          1. 10.3.5.1 Overload Protection
             1. 10.3.5.1.1 Active Current Limiting
             2. 10.3.5.1.2 Electronic Circuit Breaker with Overload Timeout, MODE = OPEN
          2. 10.3.5.2 Short Circuit Protection
             1. 10.3.5.2.1 Start-Up With Short-Circuit On Output
          3. 10.3.5.3 FAULT Response
             1. 10.3.5.3.1 Look Ahead Overload Current Fault Indicator
          4. 10.3.5.4 Current Monitoring
          5. 10.3.5.5 IN, OUT, RTN, and GND Pins
          6. 10.3.5.6 Thermal Shutdown
          7. 10.3.5.7 Low Current Shutdown Control (SHDN)
    4. 10.4 Device Functional Modes
11. 11Application and Implementation
    1. 11.1 Application Information
    2. 11.2 Typical Application
       1. 11.2.1 Design Requirements
       2. 11.2.2 Detailed Design Procedure
          1. 11.2.2.1 Step by Step Design Procedure
          2. 11.2.2.2 Programming the Current-Limit Threshold—R(ILIM) Selection
          3. 11.2.2.3 Undervoltage Lockout and Overvoltage Set Point
          4. 11.2.2.4 Programming Current Monitoring Resistor—RIMON
          5. 11.2.2.5 Setting Output Voltage Ramp Time—(tdVdT)
             1. 11.2.2.5.1 Case 1: Start-Up Without Load—Only Output Capacitance C(OUT) Draws Current During Start-Up
             2. 11.2.2.5.2 Case 2: Start-Up With Load—Output Capacitance C(OUT) and Load Draws Current During Start-Up
             3. 11.2.2.5.3 Support Component Selections—RFLTb and C(IN)
       3. 11.2.3 Application Curves
    3. 11.3 System Examples
       1. 11.3.1 Acive ORing Operation
       2. 11.3.2 Field Supply Protection in PLC, DCS I/O Modules
       3. 11.3.3 Simple 24-V Power Supply Path Protection
    4. 11.4 Do's and Don'ts
12. 12Power Supply Recommendations
    1. 12.1 Transient Protection
13. 13Layout
    1. 13.1 Layout Guidelines
    2. 13.2 Layout Example
14. 14デバイスおよびドキュメントのサポート
    1. 14.1 デバイス・サポート
    2. 14.2 ドキュメントのサポート
       1. 14.2.1 関連資料
    3. 14.3 ドキュメントの更新通知を受け取る方法
    4. 14.4 コミュニティ・リソース
    5. 14.5 商標
    6. 14.6 静電気放電に関する注意事項
    7. 14.7 Glossary
15. 15メカニカル、パッケージ、および注文情報