JAJSD08D October   2015  – November 2022 DP83867CS , DP83867E , DP83867IS

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Device Comparison
  6. 6 Pin Configuration and Functions
    1. 6.1 Pin Functions
    2. 6.2 Unused Pins
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics
    6. 7.6  Power-Up Timing
    7. 7.7  Reset Timing
    8. 7.8  MII Serial Management Timing
    9. 7.9  SGMII Timing
    10. 7.10 RGMII Timing
    11. 7.11 DP83867E Start of Frame Detection Timing
    12. 7.12 DP83867IS/CS Start of Frame Detection Timing
    13. 7.13 Timing Diagrams
    14. 7.14 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 WoL (Wake-on-LAN) Packet Detection
        1. 8.3.1.1 Magic Packet Structure
        2. 8.3.1.2 Magic Packet Example
        3. 8.3.1.3 Wake-on-LAN Configuration and Status
      2. 8.3.2 Start of Frame Detect for IEEE 1588 Time Stamp
        1. 8.3.2.1 SFD Latency Variation and Determinism
          1. 8.3.2.1.1 1000-Mb SFD Variation in Master Mode
          2. 8.3.2.1.2 1000-Mb SFD Variation in Slave Mode
          3. 8.3.2.1.3 100-Mb SFD Variation
      3. 8.3.3 Clock Output
    4. 8.4 Device Functional Modes
      1. 8.4.1 MAC Interfaces
        1. 8.4.1.1 Serial GMII (SGMII)
        2. 8.4.1.2 Reduced GMII (RGMII)
          1. 8.4.1.2.1 1000-Mbps Mode Operation
          2. 8.4.1.2.2 1000-Mbps Mode Timing
          3. 8.4.1.2.3 10- and 100-Mbps Mode
      2. 8.4.2 Serial Management Interface
        1. 8.4.2.1 Extended Address Space Access
          1. 8.4.2.1.1 Write Address Operation
          2. 8.4.2.1.2 Read Address Operation
          3. 8.4.2.1.3 Write (No Post Increment) Operation
          4. 8.4.2.1.4 Read (No Post Increment) Operation
          5. 8.4.2.1.5 Write (Post Increment) Operation
          6. 8.4.2.1.6 Read (Post Increment) Operation
          7. 8.4.2.1.7 Example of Read Operation Using Indirect Register Access
          8. 8.4.2.1.8 Example of Write Operation Using Indirect Register Access
      3. 8.4.3 Auto-Negotiation
        1. 8.4.3.1 Speed and Duplex Selection - Priority Resolution
        2. 8.4.3.2 Master and Slave Resolution
        3. 8.4.3.3 Pause and Asymmetrical Pause Resolution
        4. 8.4.3.4 Next Page Support
        5. 8.4.3.5 Parallel Detection
        6. 8.4.3.6 Restart Auto-Negotiation
        7. 8.4.3.7 Enabling Auto-Negotiation Through Software
        8. 8.4.3.8 Auto-Negotiation Complete Time
        9. 8.4.3.9 Auto-MDIX Resolution
      4. 8.4.4 Loopback Mode
        1. 8.4.4.1 Near-End Loopback
          1. 8.4.4.1.1 MII Loopback
          2. 8.4.4.1.2 PCS Loopback
          3. 8.4.4.1.3 Digital Loopback
          4. 8.4.4.1.4 Analog Loopback
        2. 8.4.4.2 External Loopback
        3. 8.4.4.3 Far-End (Reverse) Loopback
      5. 8.4.5 BIST Configuration
      6. 8.4.6 Cable Diagnostics
        1. 8.4.6.1 TDR
        2. 8.4.6.2 Energy Detect
        3. 8.4.6.3 Fast Link Detect
        4. 8.4.6.4 Speed Optimization
        5. 8.4.6.5 Mirror Mode
        6. 8.4.6.6 Interrupt
        7. 8.4.6.7 IEEE 802.3 Test Modes
    5. 8.5 Programming
      1. 8.5.1 Strap Configuration
      2. 8.5.2 LED Configuration
      3. 8.5.3 LED Operation From 1.8-V I/O VDD Supply
      4. 8.5.4 PHY Address Configuration
      5. 8.5.5 Reset Operation
        1. 8.5.5.1 Hardware Reset
        2. 8.5.5.2 IEEE Software Reset
        3. 8.5.5.3 Global Software Reset
        4. 8.5.5.4 Global Software Restart
        5. 8.5.5.5 PCS Restart
      6. 8.5.6 Power-Saving Modes
        1. 8.5.6.1 IEEE Power Down
        2. 8.5.6.2 Deep Power-Down Mode
        3. 8.5.6.3 Active Sleep
        4. 8.5.6.4 Passive Sleep
    6. 8.6 Register Maps
      1. 8.6.1   Basic Mode Control Register (BMCR)
      2. 8.6.2   Basic Mode Status Register (BMSR)
      3. 8.6.3   PHY Identifier Register #1 (PHYIDR1)
      4. 8.6.4   PHY Identifier Register #2 (PHYIDR2)
      5. 8.6.5   Auto-Negotiation Advertisement Register (ANAR)
      6. 8.6.6   Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page)
      7. 8.6.7   Auto-Negotiate Expansion Register (ANER)
      8. 8.6.8   Auto-Negotiation Next Page Transmit Register (ANNPTR)
      9. 8.6.9   Auto-Negotiation Next Page Receive Register (ANNPRR)
      10. 8.6.10  1000BASE-T Configuration Register (CFG1)
      11. 8.6.11  Status Register 1 (STS1)
      12. 8.6.12  Extended Register Addressing
        1. 8.6.12.1 Register Control Register (REGCR)
        2. 8.6.12.2 Address or Data Register (ADDAR)
      13. 8.6.13  1000BASE-T Status Register (1KSCR)
      14. 8.6.14  PHY Control Register (PHYCR)
      15. 8.6.15  PHY Status Register (PHYSTS)
      16. 8.6.16  MII Interrupt Control Register (MICR)
      17. 8.6.17  Interrupt Status Register (ISR)
      18. 8.6.18  Configuration Register 2 (CFG2)
      19. 8.6.19  Receiver Error Counter Register (RECR)
      20. 8.6.20  BIST Control Register (BISCR)
      21. 8.6.21  Status Register 2 (STS2)
      22. 8.6.22  LED Configuration Register 1 (LEDCR1)
      23. 8.6.23  LED Configuration Register 2 (LEDCR2)
      24. 8.6.24  LED Configuration Register (LEDCR3)
      25. 8.6.25  Configuration Register 3 (CFG3)
      26. 8.6.26  Control Register (CTRL)
      27. 8.6.27  Testmode Channel Control (TMCH_CTRL)
      28. 8.6.28  Robust Auto MDIX Timer Configuration Register (AMDIX_TMR_CFG)
      29. 8.6.29  Fast Link Drop Configuration Register (FLD_CFG)
      30. 8.6.30  Fast Link Drop Threshold Configuration Register (FLD_THR_CFG)
      31. 8.6.31  Configuration Register 4 (CFG4)
      32. 8.6.32  RGMII Control Register (RGMIICTL)
      33. 8.6.33  RGMII Control Register 2 (RGMIICTL2)
      34. 8.6.34  SGMII Auto-Negotiation Status (SGMII_ANEG_STS)
      35. 8.6.35  100BASE-TX Configuration (100CR)
      36. 8.6.36  Viterbi Module Configuration (VTM_CFG)
      37. 8.6.37  Skew FIFO Status (SKEW_FIFO)
      38. 8.6.38  Strap Configuration Status Register 1 (STRAP_STS1)
      39. 8.6.39  Strap Configuration Status Register 2 (STRAP_STS2)
      40. 8.6.40  BIST Control and Status Register 1 (BICSR1)
      41. 8.6.41  BIST Control and Status Register 2 (BICSR2)
      42. 8.6.42  BIST Control and Status Register 3 (BICSR3)
      43. 8.6.43  BIST Control and Status Register 4 (BICSR4)
      44. 8.6.44  Configuration for Receiver's Equalizer (CRE)
      45. 8.6.45  RGMII Delay Control Register (RGMIIDCTL)
      46. 8.6.46  Configuration of Receiver's LPF (CRLPF)
      47. 8.6.47  Enable Control of Receiver's Equalizer (ECRE)
      48. 8.6.48  PLL Clock-out Control Register (PLLCTL)
      49. 8.6.49  SGMII Control Register 1 (SGMIICTL1)
      50. 8.6.50  Sync FIFO Control (SYNC_FIFO_CTRL)
      51. 8.6.51  Loopback Configuration Register (LOOPCR)
      52. 8.6.52  DSP Configuration (DSP_CONFIG)
      53. 8.6.53  DSP Feedforward Equalizer Configuration (DSP_FFE_CFG)
      54. 8.6.54  Receive Configuration Register (RXFCFG)
      55. 8.6.55  Receive Status Register (RXFSTS)
      56. 8.6.56  Pattern Match Data Register 1 (RXFPMD1)
      57. 8.6.57  Pattern Match Data Register 2 (RXFPMD2)
      58. 8.6.58  Pattern Match Data Register 3 (RXFPMD3)
      59. 8.6.59  SecureOn Pass Register 2 (RXFSOP1)
      60. 8.6.60  SecureOn Pass Register 2 (RXFSOP2)
      61. 8.6.61  SecureOn Pass Register 3 (RXFSOP3)
      62. 8.6.62  Receive Pattern Register 1 (RXFPAT1)
      63. 8.6.63  Receive Pattern Register 2 (RXFPAT2)
      64. 8.6.64  Receive Pattern Register 3 (RXFPAT3)
      65. 8.6.65  Receive Pattern Register 4 (RXFPAT4)
      66. 8.6.66  Receive Pattern Register 5 (RXFPAT5)
      67. 8.6.67  Receive Pattern Register 6 (RXFPAT6)
      68. 8.6.68  Receive Pattern Register 7 (RXFPAT7)
      69. 8.6.69  Receive Pattern Register 8 (RXFPAT8)
      70. 8.6.70  Receive Pattern Register 9 (RXFPAT9)
      71. 8.6.71  Receive Pattern Register 10 (RXFPAT10)
      72. 8.6.72  Receive Pattern Register 11 (RXFPAT11)
      73. 8.6.73  Receive Pattern Register 12 (RXFPAT12)
      74. 8.6.74  Receive Pattern Register 13 (RXFPAT13)
      75. 8.6.75  Receive Pattern Register 14 (RXFPAT14)
      76. 8.6.76  Receive Pattern Register 15 (RXFPAT15)
      77. 8.6.77  Receive Pattern Register 16 (RXFPAT16)
      78. 8.6.78  Receive Pattern Register 17 (RXFPAT17)
      79. 8.6.79  Receive Pattern Register 18 (RXFPAT18)
      80. 8.6.80  Receive Pattern Register 19 (RXFPAT19)
      81. 8.6.81  Receive Pattern Register 20 (RXFPAT20)
      82. 8.6.82  Receive Pattern Register 21 (RXFPAT21)
      83. 8.6.83  Receive Pattern Register 22 (RXFPAT22)
      84. 8.6.84  Receive Pattern Register 23 (RXFPAT23)
      85. 8.6.85  Receive Pattern Register 24 (RXFPAT24)
      86. 8.6.86  Receive Pattern Register 25 (RXFPAT25)
      87. 8.6.87  Receive Pattern Register 26 (RXFPAT26)
      88. 8.6.88  Receive Pattern Register 27 (RXFPAT27)
      89. 8.6.89  Receive Pattern Register 28 (RXFPAT28)
      90. 8.6.90  Receive Pattern Register 29 (RXFPAT29)
      91. 8.6.91  Receive Pattern Register 30 (RXFPAT30)
      92. 8.6.92  Receive Pattern Register 31 (RXFPAT31)
      93. 8.6.93  Receive Pattern Register 32 (RXFPAT32)
      94. 8.6.94  Receive Pattern Byte Mask Register 1 (RXFPBM1)
      95. 8.6.95  Receive Pattern Byte Mask Register 2 (RXFPBM2)
      96. 8.6.96  Receive Pattern Byte Mask Register 3 (RXFPBM3)
      97. 8.6.97  Receive Pattern Byte Mask Register 4 (RXFPBM4)
      98. 8.6.98  Receive Pattern Control (RXFPATC)
      99. 8.6.99  10M SGMII Configuration (10M_SGMII_CFG)
      100. 8.6.100 I/O Configuration (IO_MUX_CFG)
      101. 8.6.101 GPIO Mux Control Register (GPIO_MUX_CTRL)
      102. 8.6.102 TDR General Configuration Register 1 (TDR_GEN_CFG1)
      103. 8.6.103 TDR Peak Locations Register 1 (TDR_PEAKS_LOC_1)
      104. 8.6.104 TDR Peak Locations Register 2 (TDR_PEAKS_LOC_2)
      105. 8.6.105 TDR Peak Locations Register 3 (TDR_PEAKS_LOC_3)
      106. 8.6.106 TDR Peak Locations Register 4 (TDR_PEAKS_LOC_4)
      107. 8.6.107 TDR Peak Locations Register 5 (TDR_PEAKS_LOC_5)
      108. 8.6.108 TDR Peak Locations Register 6 (TDR_PEAKS_LOC_6)
      109. 8.6.109 TDR Peak Locations Register 7 (TDR_PEAKS_LOC_7)
      110. 8.6.110 TDR Peak Locations Register 8 (TDR_PEAKS_LOC_8)
      111. 8.6.111 TDR Peak Locations Register 9 (TDR_PEAKS_LOC_9)
      112. 8.6.112 TDR Peak Locations Register 10 (TDR_PEAKS_LOC_10)
      113. 8.6.113 TDR Peak Amplitudes Register 1 (TDR_PEAKS_AMP_1)
      114. 8.6.114 TDR Peak Amplitudes Register 2 (TDR_PEAKS_AMP_2)
      115. 8.6.115 TDR Peak Amplitudes Register 3 (TDR_PEAKS_AMP_3)
      116. 8.6.116 TDR Peak Amplitudes Register 4 (TDR_PEAKS_AMP_4)
      117. 8.6.117 TDR Peak Amplitudes Register 5 (TDR_PEAKS_AMP_5)
      118. 8.6.118 TDR Peak Amplitudes Register 6 (TDR_PEAKS_AMP_6)
      119. 8.6.119 TDR Peak Amplitudes Register 7 (TDR_PEAKS_AMP_7)
      120. 8.6.120 TDR Peak Amplitudes Register 8 (TDR_PEAKS_AMP_8)
      121. 8.6.121 TDR Peak Amplitudes Register 9 (TDR_PEAKS_AMP_9)
      122. 8.6.122 TDR Peak Amplitudes Register 10 (TDR_PEAKS_AMP_10)
      123. 8.6.123 TDR General Status (TDR_GEN_STATUS)
      124. 8.6.124 Programmable Gain Register (PROG_GAIN)
      125. 8.6.125 MMD3 PCS Control Register (MMD3_PCS_CTRL)
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Cable Line Driver
        2. 9.2.1.2 Clock In (XI) Recommendation
        3. 9.2.1.3 Crystal Recommendations
        4. 9.2.1.4 Clock Out (CLK_OUT) Phase Noise
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 MAC Interface
          1. 9.2.2.1.1 SGMII Layout Guidelines
          2. 9.2.2.1.2 RGMII Layout Guidelines
        2. 9.2.2.2 Media Dependent Interface (MDI)
          1. 9.2.2.2.1 MDI Layout Guidelines
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Signal Traces
      2. 11.1.2 Return Path
      3. 11.1.3 Transformer Layout
      4. 11.1.4 Metal Pour
      5. 11.1.5 PCB Layer Stacking
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Related Links
    3. 12.3 Receiving Notification of Documentation Updates
    4. 12.4 サポート・リソース
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
    7. 12.7 Trademarks
      1.      Mechanical, Packaging, and Orderable Information

8.3.1.1 Magic Packet Structure

When configured for Magic Packet mode, the DP83867 scans all incoming frames addressed to the node for a specific data sequence. This sequence identifies the frame as a Magic Packet frame.

Note:

The Magic Packet should be byte aligned.

A Magic Packet frame must also meet the basic requirements for the LAN technology chosen, such as SOURCE ADDRESS, DESTINATION ADDRESS (which may be the receiving station’s IEEE address or a BROADCAST address), and CRC.

The specific Magic Packet sequence consists of 16 duplications of the IEEE address of this node, with no breaks or interruptions, followed by secure-on password if security is enabled. This sequence can be located anywhere within the packet, but must be preceded by a synchronization stream. The synchronization stream is defined as 6 bytes of FFh.

GUID-CEA40B6B-2378-4D64-A589-F003C26122C2-low.gifFigure 8-1 Magic Packet Structure