JAJSE19G October   2017  – November 2022 TUSB564

PRODUCTION DATA  

  1. 特長
  2. アプリケーション
  3. 概要
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Timing Requirements
    8. 6.8 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 USB 3.1
      2. 8.3.2 DisplayPort
      3. 8.3.3 4-Level Inputs
      4. 8.3.4 Receiver Linear Equalization
    4. 8.4 Device Functional Modes
      1. 8.4.1 Device Configuration in GPIO Mode
      2. 8.4.2 Device Configuration In I2C Mode
      3. 8.4.3 DisplayPort Mode
      4. 8.4.4 Linear EQ Configuration
      5. 8.4.5 USB3.1 Modes
      6. 8.4.6 Operation Timing – Power Up
    5. 8.5 Programming
    6. 8.6 Register Maps
      1. 8.6.1 General Register (address = 0x0A) [reset = 00000001]
      2. 8.6.2 DisplayPort Control/Status Registers (address = 0x10) [reset = 00000000]
      3. 8.6.3 DisplayPort Control/Status Registers (address = 0x11) [reset = 00000000]
      4. 8.6.4 DisplayPort Control/Status Registers (address = 0x12) [reset = 00000000]
      5. 8.6.5 DisplayPort Control/Status Registers (address = 0x13) [reset = 00000000]
      6. 8.6.6 USB3.1 Control/Status Registers (address = 0x20) [reset = 00000000]
      7. 8.6.7 USB3.1 Control/Status Registers (address = 0x21) [reset = 00000000]
      8. 8.6.8 USB3.1 Control/Status Registers (address = 0x22) [reset = 00000000]
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Support for DisplayPort UFP_D Pin Assignment E
      4. 9.2.4 PCB Insertion Loss Curves
    3. 9.3 System Examples
      1. 9.3.1 USB 3.1 Only
      2. 9.3.2 USB 3.1 and 2 Lanes of DisplayPort
      3. 9.3.3 DisplayPort Only
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 サポート・リソース
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Revision History

Changes from Revision F (September 2019) to Revision G (November 2022)

  • 文書全体にわたって表、図、相互参照の採番方法を更新Go
  • データシート全体にわたって包括的な用語を追加Go
  • MSL レベルを 2 から 1 に更新Go

Changes from Revision E (May 2019) to Revision F (September 2019)

  • Added note to disable AUX snoop to resolve interop issues with a non-compliant AUX source.Go

Changes from Revision D (November 2018) to Revision E (May 2019)

  • Added following to pin 38 description: If I2C_EN = “F”, then this pin must be set to “F” or “0”. Go
  • Changed GLF min, typ, and max values from -1, 0, 1 to -2.5, 0.5, and 3.5 respectivelyGo
  • Added GLF_LFPS_TX1/2 parameter to AC electricalGo

Changes from Revision C (February 2018) to Revision D (November 2018)

  • Changed the RNQ pin image appearance Go
  • Changed the EN pin Description in the Pin Functions tableGo
  • Changed the HPDIN pin From: I/O To: 2 Level I Go
  • Added pull-down indicator (PD) in the I/O column on FLIP/SCL and CTL0/SDA pins Go
  • Added Junction temperature to absolute maximum ratings tableGo
  • From: Internal pull-down resistance for CTL1.  To:  Internal pull-down resistance for CTL1, CTL0, FLIP, and ENGo
  • Deleted EN from Note 1 of Table 8-8 Go

Changes from Revision B (January 2018) to Revision C (February 2018)

  • Changed the column on EN From: I To: 2 Level I (PD) Go
  • Updated AUX_SBU_OVR Description field in Table 8-15 to match Table 8-6 Go

Changes from Revision A (October 2017) to Revision B (January 2018)

  • Changed From: DP0EQ_SEL To: DP3EQ_SEL Go
  • Changed From: DP3EQ_SEL To: DP0EQ_SEL Go

Changes from Revision * (October 2017) to Revision A (October 2017)

  • デバイス・ステータスを「事前情報」から「量産データ」に変更 Go
  • UFP_D ピンの割り当て C および D を、UFP_D ピンの割り当て C、D、E に変更Go
  • Added Note which describes AUX snoop feature is only supported in I2C mode. In GPIO mode, AUX snoop is disabled and all four lanes are enabled. Go