JAJSGT5L November   2006  – October 2024 TS3USB221

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics
    6. 5.6  Dynamic Electrical Characteristics, VCC = 3.3V ± 10%
    7. 5.7  Dynamic Electrical Characteristics, VCC = 2.5V ± 10%
    8. 5.8  Switching Characteristics, VCC = 3.3V ± 10%
    9. 5.9  Switching Characteristics, VCC = 2.5V ± 10%
    10. 5.10 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Low Power Mode
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 ドキュメントの更新通知を受け取る方法
    3. 9.3 サポート・リソース
    4. 9.4 Trademarks
    5. 9.5 静電気放電に関する注意事項
    6. 9.6 用語集
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

5.5 Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)(1)
PARAMETERTEST CONDITIONSMINTYP(2)MAXUNIT
VIKVCC = 3.6V, 2.7V,II = –18mA–1.8V
IINControl
inputs		VCC = 3.6V, 2.7V, 0V,VIN = 0V to 3.6V±1μA
IOZ (3)VCC = 3.6V, 2.7V,
VO = 0V to 3.6V, VI = 0V,		VIN = VCC or GND,
Switch OFF		±1μA
IOFFVCC = 0VVI/O = 0V to 3.6V±2μA
VI/O = 0V to 2.7V±1
ICCVCC = 3.6V, 2.7V,
VIN = VCC or GND,		II/O = 0V,
Switch ON or OFF		30μA
ICC
(low power mode)		VCC = 3.6V, 2.7V,
VIN = VCC or GND		Switch disabled
( OE in high state)		1μA
ΔICC (4)Control
inputs		One input at 1.8V,
Other inputs at VCC or GND		VCC = 3.6V20μA
VCC = 2.7V0.5
CinControl
inputs		VCC = 3.3V, 2.5V,VIN = 3.3V or 0V12pF
Cio(OFF)VCC = 3.3V, 2.5V,VI/O = 3.3V or 0V,Switch OFF34pF
Cio(ON)VCC = 3.3V, 2.5V,VI/O = 3.3V or 0V,Switch ON56pF
ron (5)VCC = 3V, 2.3VVI = 0V,IO = 30mA6Ω
VI = 2.4V,IO = –15mA6
ΔronVCC = 3V, 2.3VVI = 0V,IO = 30mA0.2Ω
VI = 1.7,IO = –15mA0.2
ron(flat)VCC = 3V, 2.3VVI = 0V,IO = 30mA1Ω
VI = 1.7,IO = –15mA1
(1) VIN and IIN refer to control inputs. VI, VO, II, and IO refer to data pins.
(2) All typical values are at VCC = 3.3V (unless otherwise noted), TA = 25°C.
(3) For I/O ports, the parameter IOZ includes the input leakage current.
(4) This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND.
(5) Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is determined by the lower of the voltages of the two (A or B) terminals.