JAJSUD6 April   2024 TPS23881B

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
    1. 5.1 Detailed Pin Description
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  8. 7 Parameter Measurement Information
    1. 7.1 Timing Diagrams
  9. 8 Detailed Description
    1. 8.1 Overview
      1. 8.1.1 Operating Modes
        1. 8.1.1.1 Auto
        2. 8.1.1.2 Semiauto
        3. 8.1.1.3 Manual and Diagnostic
        4. 8.1.1.4 Power Off
      2. 8.1.2 PoE Compliance Terminology
      3. 8.1.3 Channel versus Port Terminology
      4. 8.1.4 Requested Class versus Assigned Class
      5. 8.1.5 Power Allocation and Power Demotion
      6. 8.1.6 Programmable SRAM
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Port Remapping
      2. 8.3.2 Port Power Priority
      3. 8.3.3 Analog-to-Digital Converters (ADC)
      4. 8.3.4 I2C Watchdog
      5. 8.3.5 Current Foldback Protection
    4. 8.4 Device Functional Modes
      1. 8.4.1 Detection
      2. 8.4.2 Connection Check
      3. 8.4.3 Classification
      4. 8.4.4 DC Disconnect
    5. 8.5 I2C Programming
      1. 8.5.1 I2C Serial Interface
    6. 8.6 Register Maps
      1. 8.6.1 Complete Register Set
      2. 8.6.2 Detailed Register Descriptions
        1. 8.6.2.1  INTERRUPT Register
        2. 8.6.2.2  INTERRUPT MASK Register
        3. 8.6.2.3  POWER EVENT Register
        4. 8.6.2.4  DETECTION EVENT Register
        5. 8.6.2.5  FAULT EVENT Register
        6. 8.6.2.6  START/ILIM EVENT Register
        7. 8.6.2.7  SUPPLY and FAULT EVENT Register
          1. 8.6.2.7.1 Detected SRAM Faults and "Safe Mode"
        8. 8.6.2.8  CHANNEL 1 DISCOVERY Register
        9. 8.6.2.9  CHANNEL 2 DISCOVERY Register
        10. 8.6.2.10 CHANNEL 3 DISCOVERY Register
        11. 8.6.2.11 CHANNEL 4 DISCOVERY Register
        12. 8.6.2.12 POWER STATUS Register
        13. 8.6.2.13 PIN STATUS Register
        14. 8.6.2.14 OPERATING MODE Register
        15. 8.6.2.15 DISCONNECT ENABLE Register
        16. 8.6.2.16 DETECT/CLASS ENABLE Register
        17. 8.6.2.17 Power Priority / 2Pair PCUT Disable Register Name
        18. 8.6.2.18 TIMING CONFIGURATION Register
        19. 8.6.2.19 GENERAL MASK Register
        20. 8.6.2.20 DETECT/CLASS RESTART Register
        21. 8.6.2.21 POWER ENABLE Register
        22. 8.6.2.22 RESET Register
        23. 8.6.2.23 ID Register
        24. 8.6.2.24 Connection Check and Auto Class Status Register
        25. 8.6.2.25 2-Pair Police Ch-1 Configuration Register
        26. 8.6.2.26 2-Pair Police Ch-2 Configuration Register
        27. 8.6.2.27 2-Pair Police Ch-3 Configuration Register
        28. 8.6.2.28 2-Pair Police Ch-4 Configuration Register
        29. 8.6.2.29 Capacitance (Legacy PD) Detection
        30. 8.6.2.30 Power-on Fault Register
        31. 8.6.2.31 PORT RE-MAPPING Register
        32. 8.6.2.32 Channels 1 and 2 Multi Bit Priority Register
        33. 8.6.2.33 Channels 3 and 4 Multi Bit Priority Register
        34. 8.6.2.34 4-Pair Wired and Port Power Allocation Register
        35. 8.6.2.35 4-Pair Police Ch-1 and 2 Configuration Register
        36. 8.6.2.36 4-Pair Police Ch-3 and 4 Configuration Register
        37. 8.6.2.37 TEMPERATURE Register
        38. 8.6.2.38 4-Pair Fault Configuration Register
        39. 8.6.2.39 INPUT VOLTAGE Register
        40. 8.6.2.40 CHANNEL 1 CURRENT Register
        41. 8.6.2.41 CHANNEL 2 CURRENT Register
        42. 8.6.2.42 CHANNEL 3 CURRENT Register
        43. 8.6.2.43 CHANNEL 4 CURRENT Register
        44. 8.6.2.44 CHANNEL 1 VOLTAGE Register
        45. 8.6.2.45 CHANNEL 2 VOLTAGE Register
        46. 8.6.2.46 CHANNEL 3 VOLTAGE Register
        47. 8.6.2.47 CHANNEL 4 VOLTAGE Register
        48. 8.6.2.48 2x FOLDBACK SELECTION Register
        49. 8.6.2.49 FIRMWARE REVISION Register
        50. 8.6.2.50 I2C WATCHDOG Register
        51. 8.6.2.51 DEVICE ID Register
        52. 8.6.2.52 CHANNEL 1 DETECT RESISTANCE Register
        53. 8.6.2.53 CHANNEL 2 DETECT RESISTANCE Register
        54. 8.6.2.54 CHANNEL 3 DETECT RESISTANCE Register
        55. 8.6.2.55 CHANNEL 4 DETECT RESISTANCE Register
        56. 8.6.2.56 CHANNEL 1 DETECT CAPACITANCE Register
        57. 8.6.2.57 CHANNEL 2 DETECT CAPACITANCE Register
        58. 8.6.2.58 CHANNEL 3 DETECT CAPACITANCE Register
        59. 8.6.2.59 CHANNEL 4 DETECT CAPACITANCE Register
        60. 8.6.2.60 CHANNEL 1 ASSIGNED CLASS Register
        61. 8.6.2.61 CHANNEL 2 ASSIGNED CLASS Register
        62. 8.6.2.62 CHANNEL 3 ASSIGNED CLASS Register
        63. 8.6.2.63 CHANNEL 4 ASSIGNED CLASS Register
        64. 8.6.2.64 AUTO CLASS CONTROL Register
        65. 8.6.2.65 CHANNEL 1 AUTO CLASS POWER Register
        66. 8.6.2.66 CHANNEL 2 AUTO CLASS POWER Register
        67. 8.6.2.67 CHANNEL 3 AUTO CLASS POWER Register
        68. 8.6.2.68 CHANNEL 4 AUTO CLASS POWER Register
        69. 8.6.2.69 ALTERNATIVE FOLDBACK Register
        70. 8.6.2.70 SRAM CONTROL Register
          1. 8.6.2.70.1 SRAM START ADDRESS (LSB) Register
          2. 8.6.2.70.2 SRAM START ADDRESS (MSB) Register
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Introduction to PoE
        1. 9.1.1.1 2-Pair Versus 4-Pair Power and the New IEEE802.3bt Standard
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Connections on Unused Channels
        2. 9.2.2.2 Power Pin Bypass Capacitors
        3. 9.2.2.3 Per Port Components
        4. 9.2.2.4 System Level Components (not Shown in the Schematic Diagrams)
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 VDD
      2. 9.3.2 VPWR
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
        1. 9.4.1.1 Kelvin Current Sensing Resistors
      2. 9.4.2 Layout Example
        1. 9.4.2.1 Component Placement and Routing Guidelines
          1. 9.4.2.1.1 Power Pin Bypass Capacitors
          2. 9.4.2.1.2 Per-Port Components
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 ドキュメントの更新通知を受け取る方法
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 静電気放電に関する注意事項
    6. 10.6 用語集
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

8.5.1 I2C Serial Interface

The TPS23881B features a 3-wire I2C interface, using SDAI, SDAO, and SCL. Each transmission includes a START condition sent by the controller, followed by the device address (7-bit) with R/W bit, a register address byte, then one or two data bytes and a STOP condition. The recipient sends an acknowledge bit following each byte transmitted. SDAI/SDAO is stable while SCL is high except during a START or STOP condition.

Figure 8-6 and Figure 8-7 show read and write operations through I2C interface, using configuration A or B (see Table 8-25 for more details). The parametric read operation is applicable to ADC conversion results. The TPS23881B features quick access to the latest addressed register through I2C bus. When a STOP bit is received, the register pointer is not automatically reset.

It is also possible to perform a write operation to many TPS23881B devices at the same time. The target address during this broadcast access is 0x7F, as shown in PIN STATUS Register. Depending on which configuration (A or B) is selected, a global write proceeds as following:

  • Config A: Both 4-port devices (1 to 4 and 5 to 8) are addressed at same time.
  • Config B: The whole device is addressed.
TPS23881B I2C interface Read and Write Protocol – Configuration A Figure 8-6 I2C interface Read and Write Protocol – Configuration A
TPS23881B I2C interface Read and Write Protocol – Configuration B Figure 8-7 I2C interface Read and Write Protocol – Configuration B