SLVA275C january   2010  – may 2023 UCD9081

 

  1.   Abstract
  2.   Trademarks
  3. 1Introduction
  4. 2Hardware
    1. 2.1 Package: RHB (S-PQFP-N32), 32-Pin Plastic Quad Flatpack
    2. 2.2 Hardware and Pinout
    3. 2.3 Detailed Pin Descriptions
      1. 2.3.1 RST
      2. 2.3.2 SDA
      3. 2.3.3 SCL
      4. 2.3.4 ADDRx
      5. 2.3.5 ROSC
  5. 3Software
    1. 3.1 Data File Format
    2. 3.2 I2C Transactions
    3. 3.3 Device Version
    4. 3.4 Checksum
    5. 3.5 Sample Configuration Data File
      1. 3.5.1 Factory Default
      2. 3.5.2 EVM Default Configuration
    6. 3.6 I2C Write and Read Transaction Formats
      1. 3.6.1 I2C Write Transaction
      2. 3.6.2 I2C Read Transaction
    7. 3.7 Pseudo I2C Write and Read Transactions
      1. 3.7.1 UCD9081 I2C Transactions for Writing User Data and PARAMS
      2. 3.7.2 UCD9081 I2C Transactions for Reading User Data and PARAMS
  6. 4User Configuration
    1. 4.1 Configuration Parameter Memory Map
    2. 4.2 Configuration Parameter Detail
      1. 4.2.1  GpDir
      2. 4.2.2  NegateEnablePolarity
      3. 4.2.3  SeqEventPending
      4. 4.2.4  SequenceEventParameters
      5. 4.2.5  SequenceEventLink
      6. 4.2.6  SequenceEventData
      7. 4.2.7  DependencyMasks
      8. 4.2.8  UnderVoltageThresholds
      9. 4.2.9  OverVoltageThresholds
      10. 4.2.10 RampTime
      11. 4.2.11 OutOfRegulationWidth
      12. 4.2.12 UnsequenceTime
      13. 4.2.13 EnablePolarity
      14. 4.2.14 SaveRailLog
      15. 4.2.15 ReferenceSelect
      16. 4.2.16 LastUnusedSeq
      17. 4.2.17 IgnoreGlitchAlarms
      18. 4.2.18 IgnoreFlashErrorLog
      19. 4.2.19 Checksum
  7. 5Additional Considerations
    1. 5.1 Embedded Application
    2. 5.2 Timing
      1. 5.2.1 UCD9081 Startup
      2. 5.2.2 Clock Stretching After Flash Erase
      3. 5.2.3 Bit Timeout
      4. 5.2.4 Byte or Transaction Timeout
  8. 6References
  9. 7Revision History

4.2.11 OutOfRegulationWidth

The OutOfRegulationWidth field in the configuration parameters specifies the maximum amount of time that the rail is allowed to be out of regulation before an error is declared (glitch duration). The address map for these registers is as follows:

AddressSizeDefault ValueDescription
0xE14020x0010The out-of-regulation duration permissible without flagging error for rail 1
0xE14220x0010The out-of-regulation duration permissible without flagging error for rail 2
0xE14420x0010The out-of-regulation duration permissible without flagging error for rail 3
0xE14620x0010The out-of-regulation duration permissible without flagging error for rail 4
0xE14820x0010The out-of-regulation duration permissible without flagging error for rail 5
0xE14A20x0010The out-of-regulation duration permissible without flagging error for rail 6
0xE14C20x0010The out-of-regulation duration permissible without flagging error for rail 7
0xE14E20x0010The out-of-regulation duration permissible without flagging error for rail 8

The contents of this register are as follows:

GUID-CA285978-FFD6-4D97-BB25-C0A6C2DEA4A5-low.gif