Input | Output | Supply | |||
---|---|---|---|---|---|
ViMin | ViMax | VoMin | VoMax | Vcc | Vee |
–2.45V | +2.45V | 0.05V | 4.95V | 5V | 0V |
Gain | Low Cutoff Frequency (fl) | High Cutoff Frequency (fh) | Vref |
---|---|---|---|
1V/V | 1kHz | 10kHz | 2.5V |
Design Description
This circuit is a single-supply, 2nd-order Sallen-Key (SK) band-pass (BP) filter. It is designed by cascading an SK low-pass filter and an SK high-pass filter. Vref provides a DC offset to accommodate for a single supply.
Design Notes
Design Steps
This BP filter design involves two cascaded filters, a low-pass (LP) filter and a high-pass (HP) filter. The lower cutoff frequency (fl) of the BP filter is 1kHz and the higher cutoff frequency (fh) is 10kHz. The design steps show an LP filter design with fh of 10kHz and an HP filter design with fl of 1kHz. See the SK LP filter design and SK HP filter design in the circuit cookbook for details on transfer function equations and calculations.
LP Filter Design
HP Filter Design
Design Simulations
AC Simulation Results
Transient Simulation Results
The following image shows a filter output in response to a 5Vpp, 100Hz input signal (gain = 0.01V/V).
The following transient
simulation result shows a filter output in response to a 5Vpp, 5kHz input
signal
(gain = 1V/V).
The following image shows a filter output in response to a 5Vpp, 100kHz input signal (gain = 0.01V/V).
Design References
Design Featured Op Amp
TLV9062 | |
---|---|
Vss | 1.8V to 5.5V |
VinCM | Rail-to-Rail |
Vout | Rail-to-Rail |
Vos | 0.3mV |
Iq | 538µA |
Ib | 0.5pA |
UGBW | 10MHz |
SR | 6.5V/µs |
# of Channels | 1, 2, 4 |
www.ti.com/product/TLV9062 |
Design Alternate Op Amp
Parametric Search | |
---|---|
Vss | 5V |
VinCM | Rail-to-Rail |
Vout | Rail-to-Rail |
UGBW | 1MHz |
SR | > 5V/µS |
# of Channels | 2 |
www.ti.com/parametricsearch |
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2025, Texas Instruments Incorporated