DLPS272A May   2024  – December 2024 DLP472NE

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  Storage Conditions
    3. 5.3  ESD Ratings
    4. 5.4  Recommended Operating Conditions
    5.     11
    6.     12
    7. 5.5  Thermal Information
    8. 5.6  Electrical Characteristics
    9. 5.7  Switching Characteristics
    10. 5.8  Timing Requirements
    11. 5.9  System Mounting Interface Loads
    12. 5.10 Micromirror Array Physical Characteristics
    13. 5.11 Micromirror Array Optical Characteristics
    14. 5.12 Window Characteristics
    15. 5.13 Chipset Component Usage Specification
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Power Interface
      2. 6.3.2 Timing
    4. 6.4 Device Functional Modes
    5. 6.5 Optical Interface and System Image Quality Considerations
      1. 6.5.1 Numerical Aperture and Stray Light Control
      2. 6.5.2 Pupil Match
      3. 6.5.3 Illumination Overfill
    6. 6.6 Micromirror Array Temperature Calculation
    7. 6.7 Micromirror Power Density Calculation
    8. 6.8 Window Aperture Illumination Overfill Calculation
    9. 6.9 Micromirror Landed-On/Landed-Off Duty Cycle
      1. 6.9.1 Definition of Micromirror Landed-On/Landed-Off Duty Cycle
      2. 6.9.2 Landed Duty Cycle and Useful Life of the DMD
      3. 6.9.3 Landed Duty Cycle and Operational DMD Temperature
      4. 6.9.4 Estimating the Long-Term Average Landed Duty Cycle of a Product or Application
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
      3. 7.2.3 Application Curve
    3. 7.3 Temperature Sensor Diode
  9. 8 Power Supply Recommendations
    1. 8.1 DMD Power Supply Power-Up Procedure
    2. 8.2 DMD Power Supply Power-Down Procedure
  10. 9 Layout
    1. 9.1 Layout Guidelines
    2. 9.2 Impedance Requirements
    3. 9.3 Layers
    4. 9.4 Trace Width, Spacing
    5. 9.5 Power
    6. 9.6 Trace Length Matching Recommendations
  11. 10Device and Documentation Support
    1. 10.1 Third-Party Products Disclaimer
    2. 10.2 Device Support
      1. 10.2.1 Device Nomenclature
      2. 10.2.2 Device Markings
    3. 10.3 Documentation Support
      1. 10.3.1 Related Documentation
    4. 10.4 Receiving Notification of Documentation Updates
    5. 10.5 Support Resources
    6. 10.6 Trademarks
    7. 10.7 Electrostatic Discharge Caution
    8. 10.8 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Package Option Addendum
      1. 12.1.1 Packaging Information

6.7 Micromirror Power Density Calculation

The calculation of the optical power density of the illumination on the DMD in the different wavelength bands uses the total measured optical power on the DMD, percent illumination overfill, area of the active array, and ratio of the spectrum in the wavelength band of interest to the total spectral optical power.

  • ILLUV = [OPUV-RATIO × QINCIDENT] × 1000 (mW/W) ÷ AILL (mW/cm2)
  • ILLVIS = [OPVIS-RATIO × QINCIDENT] ÷ AILL (W/cm2)
  • ILLIR = [OPIR-RATIO × QINCIDENT] × 1000 (mW/W) ÷ AILL (mW/cm2)
  • ILLBLU = [OPBLU-RATIO × QINCIDENT] ÷ AILL (W/cm2)
  • ILLBLU1 = [OPBLU1-RATIO × QINCIDENT] ÷ AILL (W/cm2)
  • AILL = AARRAY ÷ (1 – OVILL) (cm2)

where:

  • ILLUV = UV illumination power density on the DMD (mW/cm2)
  • ILLVIS = VIS illumination power density on the DMD (W/cm2)
  • ILLIR = IR illumination power density on the DMD (mW/cm2)
  • ILLBLU = BLU illumination power density on the DMD (W/cm2)
  • ILLBLU1 = BLU1 illumination power density on the DMD (W/cm2)
  • AILL = illumination area on the DMD (cm2)
  • QINCIDENT = total incident optical power on DMD (W) (measured)
  • AARRAY = area of the array (cm 2) (data sheet)
  • OVILL = percent of total illumination on the DMD outside the array (%) (optical model)
  • OPUV-RATIO = ratio of the optical power for wavelengths <410nm to the total optical power in the illumination spectrum (spectral measurement)
  • OPVIS-RATIO = ratio of the optical power for wavelengths ≥410nm and ≤800nm to the total optical power in the illumination spectrum (spectral measurement)
  • OPIR-RATIO = ratio of the optical power for wavelengths >800nm to the total optical power in the illumination spectrum (spectral measurement)
  • OPBLU-RATIO = ratio of the optical power for wavelengths ≥410nm and ≤475nm to the total optical power in the illumination spectrum (spectral measurement)
  • OPBLU1-RATIO = ratio of the optical power for wavelengths ≥410nm and ≤440nm to the total optical power in the illumination spectrum (spectral measurement)

The illumination area varies and depends on the illumination overfill. The total illumination area on the DMD is the array area and the overfill area around the array. The optical model is used to determine the percent of the total illumination on the DMD that is outside the array (OVILL) and the percent of the total illumination that is on the active array. From these values, the illumination area (AILL) is calculated. The illumination is assumed to be uniform across the entire array.

From the measured illumination spectrum, the ratio of the optical power in the wavelength bands of interest to the total optical power is calculated.

Sample calculation:

Equation 12. QINCIDENT = 25W (measured)
Equation 13. AARRAY = (10.368mm × 5.832mm) ÷ 100cm2/mm2 = 0.6047cm2 (data sheet)
Equation 14. OVILL = 16.3% (optical model)
Equation 15. OPUV-RATIO = 0.00017 (spectral measurement)
Equation 16. OPVIS-RATIO = 0.99977 (spectral measurement)
Equation 17. OPIR-RATIO = 0.00006 (spectral measurement)
Equation 18. OPBLU-RATIO = 0.28100 (spectral measurement)
Equation 19. OPBLU1-RATIO = 0.03200 (spectral measurement)
Equation 20. AILL = 0.6047cm2 ÷ (1 – 0.163) = 0.7224cm2
Equation 21. ILLUV = [0.00017 × 25W] × 1000mW/W ÷ 0.7224cm2 = 5.883mW/cm2
Equation 22. ILLVIS = [0.99977 × 25W] ÷ 0.7224cm2 = 34.60W/cm2
Equation 23. ILLIR = [0.00006 × 25W] × 1000mW/W ÷ 0.7224cm2 = 2.076mW/cm2
Equation 24. ILLBLU = [0.28100 × 25W] ÷ 0.7224cm2 = 9.72W/cm2
Equation 25. ILLBLU1 = [0.03200 × 25W] ÷ 0.7224cm2 = 1.11W/cm2