SBASAV2 October   2024 ADS9212

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Timing Diagrams
    9. 5.9 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Analog Inputs
        1. 6.3.1.1 Input Clamp Protection Circuit
        2. 6.3.1.2 Programmable Gain Amplifier (PGA)
        3. 6.3.1.3 Wide-Common-Mode Voltage Rejection Circuit
        4. 6.3.1.4 Gain Error Calibration
      2. 6.3.2 ADC Transfer Function
      3. 6.3.3 ADC Sampling Clock Input
      4. 6.3.4 Reference
        1. 6.3.4.1 Internal Reference Voltage
        2. 6.3.4.2 External Reference Voltage
      5. 6.3.5 Data Interface
        1. 6.3.5.1 Data Clock Output
        2. 6.3.5.2 ADC Output Data Randomizer
        3. 6.3.5.3 Test Patterns for Data Interface
          1. 6.3.5.3.1 Fixed Pattern
          2. 6.3.5.3.2 Digital Ramp
          3. 6.3.5.3.3 Alternating Test Pattern
    4. 6.4 Device Functional Modes
      1. 6.4.1 Power-Down
      2. 6.4.2 Reset
      3. 6.4.3 Initialization Sequence
      4. 6.4.4 Normal Operation
    5. 6.5 Programming
      1. 6.5.1 Register Write
      2. 6.5.2 Register Read
      3. 6.5.3 Multiple Devices: Daisy-Chain Topology for SPI Configuration
        1. 6.5.3.1 Register Write With Daisy-Chain
        2. 6.5.3.2 Register Read With Daisy-Chain
  8. 7 Register Map
    1. 7.1 Register Bank 0
    2. 7.2 Register Bank 1
    3. 7.3 Register Bank 2
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Parametric Measurement Unit (PMU)
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
      4. 8.2.4 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

6.3.5 Data Interface

The ADS9212 supports 2-lane and 4-lane mode with single-data-rate (SDR) and double-data-rate (DDR) interface modes. The data interface can be selected using the configuration SPI as described in Table 6-7. The ADC generates the data (D[3:0]), data clock (DCLKOUT), and frame clock (FCLKOUT) in response to the sampling clock signal on the SMPL_CLK input pin. The 18-bit ADC conversion result is output MSB first in a 24-bit data packet and the last six bits are zeroes.

The data interface signals can be described as:

  • D[3:0]: Data output from the ADC. In 4-lane mode all four lanes are used, whereas in 2-lane mode D3 and D1 are used to output ADC data.
  • DCLKOUT: Data clock output from the ADC.
  • FCLKOUT: Frame clock output from the ADC delimiting each set of 2-channel data.

Use the registers in Table 6-7 to configure the data interface.

Table 6-7 Register Configurations For Interface Modes
INTERFACE MODE FIGURE DATA_RATE
(Address = 0xC1)		 DATA_LANES
(Address = 0xC1)
4-lane, DDR Figure 5-2 0 0
2-lane, DDR Figure 5-3 0 1
4-lane, SDR Figure 5-4 1 0
2-lane, SDR Figure 5-5 1 1