SCES959A December   2023  – April 2024 TXV0108

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics
    6. 5.6  Switching Characteristics, VCCA = 1.2 ± 0.06 V
    7. 5.7  Switching Characteristics, VCCA = 1.8 ± 0.15 V
    8. 5.8  Switching Characteristics, VCCA = 2.5 ± 0.2 V
    9. 5.9  Switching Characteristics, VCCA = 3.3 ± 0.3 V
    10. 5.10 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1 Load Circuit and Voltage Waveforms
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Balanced High-Drive CMOS Push-Pull Outputs
      2. 7.3.2 Partial Power Down (Ioff)
      3. 7.3.3 VCC Isolation and VCC Disconnect (Ioff-float)
      4. 7.3.4 Over-Voltage Tolerant Inputs
      5. 7.3.5 Negative Clamping Diodes
      6. 7.3.6 Fully Configurable Dual-Rail Design
      7. 7.3.7 Supports Timing Sensitive Translation
      8. 7.3.8 Integrated Damping Resistor and Impedance Matching
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 System Examples
      1. 8.3.1 Solving Power Sequencing Challenges with the TXV0108
    4. 8.4 Power Supply Recommendations
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
      2. 8.5.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

6.1 Load Circuit and Voltage Waveforms

Unless otherwise noted, all input pulses are supplied by generators having the following characteristics:

  • f = 1MHz
  • ZO = 50Ω
  • Δt/ΔV ≤ 1ns/V

GUID-F69EA5FA-85D4-4CF2-BD87-F449FB37C9BE-low.gif
A. CL includes probe and jig capacitance.
Figure 6-1 Load Circuit
Table 6-1 Load Circuit Conditions
ParameterVCCORLCLS1VTP
tpdPropagation (delay) time1.14V – 3.6V2kΩ

15pF

OpenN/A
ten, tdisEnable time, disable time1.14V – 3.6V2kΩ15pF2 × VCCO0.15V
ten, tdisEnable time, disable time1.14V – 3.6V2kΩ15pFGND0.15V
GUID-20231113-SS0I-ZPGH-5B6Z-83HNV7CNDJ1J-low.svg
  1. The greater between tPLH and tPHL is the same as tpd.
  2. VOH and VOL are typical output voltage levels that occur with specified RL, CL, and S1
Figure 6-2 Propagation Delay
GUID-20231113-SS0I-D0WC-MTDR-75FDWK5DDRJS-low.svg
  1. VOH and VOL are typical output voltage levels that occur with specified RL, CL, and S1
Figure 6-3 Input and Output Rise and Fall Time
GUID-6D38ACC0-6D77-4DEA-9BC7-BD598F2068FC-low.gif
A. Output waveform on the condition that input is driven to a valid Logic Low.
B. Output waveform on the condition that input is driven to a valid Logic High.
C. VCCO is the supply pin associated with the output port.
D. VOH and VOL are typical output voltage levels with specified RL, CL, and S1.
Figure 6-4 Enable Time And Disable Time