Table 22-9 lists the conditions that stop SDHS data conversion. The SDHSRIS.ACQDONE bit is set to 1 to indicate that data conversion has been stopped (either incomplete or complete). When the previous data conversion has been forced to stopped before completion, the SDHSRIS.ISTOP bit is set to 1 to indicate that data conversion has been interrupted (incomplete).
Table 22-9 SDHS Conversion Stop Conditions
Stop Condition
SDHSCTL0.TRGSRC
SDHSCTL0.AUTOSSDIS
SDHSCTL2.SMPCTLOFF
Result
Number of samples = SDHSCTL2.SMPSZ + 1
Don't care
Don't care
0
SDHS power
No change
Data conversion
Stop
SDHSRIS.ISTOP
No change
SDHS_ACQDONE (to ASQ)
Assert
SDHSRIS.ACQDONE
Assert
Don't care
Don't care
1
Not supported
The ASQ stops the SDHS operation (ACQ_SDHSSTOP: 0 → 1) caused by:
UUPSCTL.USSSTOP = 0 → 1
UUPSCTL.USSPWRDN = 0 →1
SAPHASCTL0.STOP = 0 → 1
Enter debug mode while the SDHS is performing data conversion
Don't care
Don't care
Don't care
SDHS power
No change
Data conversion
Stop
SDHSRIS.ISTOP
Assert
SDHS_ACQDONE (to ASQ)
Assert
SDHSRIS.ACQDONE
Assert
SDHSCTL4.SDHSON: 1 → 0
0
Don't care
0
SDHS power
Power off
Data conversion
Stop
SDHSRIS.ISTOP
Assert
SDHS_ACQDONE (to ASQ)
Assert
SDHSRIS.ACQDONE
Assert
1
SDHS power
Power off
Data conversion
Stop
SDHSRIS.ISTOP
No change
SDHS_ACQDONE (to ASQ)
Assert
SDHSRIS.ACQDONE
Assert
1
Don't care
Don't care
Not supported
ASQ_ACQARM: 1 → 0 (from ASQ)
0
Don't care
Don't care
Not supported
1
Don't care
0
SDHS power
Power off
Data conversion
Stop
SDHSRIS.ISTOP
Assert
SDHS_ACQDONE (to ASQ)
Assert
SDHSRIS.ACQDONE
Assert
SDHS power
Power off
Data conversion
Stop
SDHSRIS.ISTOP
No change
SDHS_ACQDONE (to ASQ)
Assert
SDHSRIS.ACQDONE
Assert
SDHSCTL5.SSTART: 1 → 0
0
0
Don't care
Not supported
1
0
SDHS power
No change
Data conversion
Stop
SDHSRIS.ISTOP
Assert
SDHS_ACQDONE (to ASQ)
Assert
SDHSRIS.ACQDONE
Assert
1
SDHS power
No change
Data conversion
Stop
SDHSRIS.ISTOP
No change
SDHS_ACQDONE (to ASQ)
Assert
SDHSRIS.ACQDONE
Assert
1
Don't care
Don't care
Not supported
ASQ_ACQTRG: 1 → 0 (from ASQ)
0
Don't care
Don't care
Not supported
1
0
Don't care
Not supported
1
0
SDHS power
No change
Data conversion
Stop
SDHSRIS.ISTOP
Assert
SDHS_ACQDONE (to ASQ)
Assert
SDHSRIS.ACQDONE
Assert
1
SDHS power
No change
Data conversion
Stop
SDHSRIS.ISTOP
No change
SDHS_ACQDONE (to ASQ)
Assert
SDHSRIS.ACQDONE
Assert
The stop conditions listed in Table 22-9 can occur when data conversion has already completed or has not started. Table 22-10 summarizes how the SDHS responds to the signals when no data conversion is ongoing.
Table 22-10 SDHS Response to Conversion Stop Signals When Data Conversion is Not Running