SLVSGS9E March   2023  – June 2024 TPS61299

PRODUCTION DATA  

  1.   1
  2. Features
  3. Applications
  4. Description
  5. Device Comparison Table
  6. Pin Configuration and Functions
  7. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 System Characteristics
    7. 6.7 Typical Characteristics
  8. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Boost Control Operation
      2. 7.3.2  Version Detection
      3. 7.3.3  Under-voltage Lockout
      4. 7.3.4  Switching Frequency
      5. 7.3.5  Input Current Limit
      6. 7.3.6  Enable and Disable
      7. 7.3.7  Soft-Start Timing
      8. 7.3.8  Down Mode
      9. 7.3.9  Pass-Through Operation
      10. 7.3.10 Output Short-to-Ground Protection
      11. 7.3.11 Thermal Shutdown
    4. 7.4 Device Functional Modes
      1. 7.4.1 Fast Load Transient Mode and Normal Mode
  9. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application-Li-ion Battery to 5V Boost Converter Under Fast Mode
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Maximum Output Current
        2. 8.2.2.2 Inductor Selection
        3. 8.2.2.3 Output Capacitor Selection
        4. 8.2.2.4 Input Capacitor Selection
      3. 8.2.3 Application Curves
    3. 8.3 Typical Application-Li-ion Battery to 5V Boost Converter Under Normal Mode
      1. 8.3.1 Design Requirements
      2. 8.3.2 Application Curves
    4. 8.4 TPS61299xA Typical Application-Li-ion Battery to 5V Boost Converter Under Normal Mode
      1. 8.4.1 Design Requirements
      2. 8.4.2 Application Curves
    5. 8.5 Power Supply Recommendations
    6. 8.6 Layout
      1. 8.6.1 Layout Guidelines
      2. 8.6.2 Layout Example
    7. 8.7 Thermal Information
  10. Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Switching Frequency

The TPS61299x/xA boost converter does not have fixed frequency and it maintains a constant inductor ripple current in the range of 350mA, so the frequency is determined by the operation condition. The frequency is approximately 3MHz, the input is 3.6V, output is 5V, inductor is 1μH. Refer to to calculate the efficiency. The estimated switching frequency ƒ in continuous current mode can be calculated by Equation 1. The switching frequency is not a constant value, but is determined by induction, input voltage, and output voltage.

Equation 1. f   =   V I N   ×   ( V O U T -   V I N   ×   Ƞ ) L   ×   I L H   ×   V O U T

where

  • L is the inductor value
  • VIN is the input voltage
  • VOUT is the output voltage