SNVSA06C March   2015  – August 2018 LP8758-B0

PRODUCTION DATA.  

1. 1 Features
2. 2 Applications
3. 3 Description
4. 4 Simplified Schematic
   1.     Efficiency vs Output Current (VIN = 3.7 V)
5. 5 Revision History
6. 6 Pin Configuration and Functions
   1.     Pin Functions
7. 7 Specifications
   1. 7.1 Absolute Maximum Ratings
   2. 7.2 ESD Ratings
   3. 7.3 Recommended Operating Conditions
   4. 7.4 Thermal Information
   5. 7.5 Electrical Characteristics
   6. 7.6 I2C Serial Bus Timing Parameter
   7. 7.7 Switching Characteristics
   8. 7.8 Typical Characteristics
8. 8 Detailed Description
   1. 8.1 Overview
      1. 8.1.1 Buck Information
         1. 8.1.1.1 Operating Modes
         2. 8.1.1.2 Features
         3. 8.1.1.3 Programmability
   2. 8.2 Functional Block Diagram
   3. 8.3 Feature Description
      1. 8.3.1 Multi-Phase DC-DC Converters
         1. 8.3.1.1 Overview
         2. 8.3.1.2 Multi-Phase Operation and Phase Adding/Shedding
         3. 8.3.1.3 Transition Between PWM and PFM Modes
         4. 8.3.1.4 Multi-Phase Switcher Configurations
         5. 8.3.1.5 Buck Converter Load Current Measurement
         6. 8.3.1.6 Spread-Spectrum Mode
      2. 8.3.2 Power-Up
      3. 8.3.3 Regulator Control
         1. 8.3.3.1 Enabling and Disabling Regulator
         2. 8.3.3.2 Changing Output Voltage
      4. 8.3.4 Device Reset Scenarios
      5. 8.3.5 Diagnosis and Protection Features
         1. 8.3.5.1 Warnings for Diagnosis (Interrupt)
            1. 8.3.5.1.1 Output Current Limit
            2. 8.3.5.1.2 Thermal Warning
         2. 8.3.5.2 Protection (Regulator Disable)
            1. 8.3.5.2.1 Short-Circuit and Overload Protection
            2. 8.3.5.2.2 Thermal Shutdown
         3. 8.3.5.3 Fault (Power Down)
            1. 8.3.5.3.1 Undervoltage Lockout
      6. 8.3.6 Digital Signal Filtering
   4. 8.4 Device Functional Modes
      1. 8.4.1 Modes of Operation
   5. 8.5 Programming
      1. 8.5.1 I2C-Compatible Interface
         1. 8.5.1.1 Data Validity
         2. 8.5.1.2 Start and Stop Conditions
         3. 8.5.1.3 Transferring Data
         4. 8.5.1.4 I2C-Compatible Chip Address
         5. 8.5.1.5 Auto Increment Feature
   6. 8.6 Register Maps
      1. 8.6.1 Register Descriptions
         1. 8.6.1.1  DEV_REV
         2. 8.6.1.2  OTP_REV
         3. 8.6.1.3  BUCK0_CTRL1
         4. 8.6.1.4  BUCK0_CTRL2
         5. 8.6.1.5  BUCK1_CTRL2
         6. 8.6.1.6  BUCK2_CTRL2
         7. 8.6.1.7  BUCK3_CTRL2
         8. 8.6.1.8  BUCK0_VOUT
         9. 8.6.1.9  BUCK0_FLOOR_VOUT
         10. 8.6.1.10 BUCK0_DELAY
         11. 8.6.1.11 RESET
         12. 8.6.1.12 CONFIG
         13. 8.6.1.13 INT_TOP
         14. 8.6.1.14 INT_BUCK_0_1
         15. 8.6.1.15 INT_BUCK_2_3
         16. 8.6.1.16 TOP_STAT
         17. 8.6.1.17 BUCK_0_1_STAT
         18. 8.6.1.18 BUCK_2_3_STAT
         19. 8.6.1.19 TOP_MASK
         20. 8.6.1.20 BUCK_0_1_MASK
         21. 8.6.1.21 BUCK_2_3_MASK
         22. 8.6.1.22 SEL_I_LOAD
         23. 8.6.1.23 I_LOAD_2
         24. 8.6.1.24 I_LOAD_1
9. 9 Application and Implementation
   1. 9.1 Application Information
   2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
         1. 9.2.2.1 Application Components
            1. 9.2.2.1.1 Inductor Selection
            2. 9.2.2.1.2 Input Capacitor Selection
            3. 9.2.2.1.3 Output Capacitor Selection
      3. 9.2.3 Application Curves
10. 10Power Supply Recommendations
11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
12. 12Device and Documentation Support
    1. 12.1 Device Support
       1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 Documentation Support
       1. 12.2.1 Related Documentation
    3. 12.3 Receiving Notification of Documentation Updates
    4. 12.4 Community Resources
    5. 12.5 Trademarks
    6. 12.6 Electrostatic Discharge Caution
    7. 12.7 Glossary
13. 13Mechanical, Packaging, and Orderable Information