SPRACN9F May   2023  – August 2024 AM67 , AM67A , AM68 , AM68A , AM69 , AM69A , DRA821U , DRA821U-Q1 , DRA829J , DRA829J-Q1 , DRA829V , DRA829V-Q1 , TDA4AEN-Q1 , TDA4AH-Q1 , TDA4AL-Q1 , TDA4AP-Q1 , TDA4VE-Q1 , TDA4VEN-Q1 , TDA4VH-Q1 , TDA4VL-Q1 , TDA4VM , TDA4VM-Q1 , TDA4VP-Q1

 

  1.   1
  2.   Jacinto7 AM6x/TDA4x/DRA8x LPDDR4 Design Guidelines
  3.   Trademarks
  4. 1Overview
    1. 1.1 Supporting Documentation
    2. 1.2 Board Designs Supported
    3. 1.3 General Board Layout Guidelines
    4. 1.4 PCB Stack-Up
    5. 1.5 Bypass Capacitors
      1. 1.5.1 Bulk Bypass Capacitors
      2. 1.5.2 High-Speed Bypass Capacitors
    6. 1.6 Velocity Compensation
  5. 2LPDDR4 Board Design and Layout Guidance
    1. 2.1  LPDDR4 Introduction
    2. 2.2  LPDDR4 Device Implementations Supported
    3. 2.3  LPDDR4 Interface Schematics
    4. 2.4  Compatible JEDEC LPDDR4 Devices
    5. 2.5  Placement
    6. 2.6  LPDDR4 Keepout Region
    7. 2.7  Net Classes
    8. 2.8  LPDDR4 Signal Termination
    9. 2.9  LPDDR4 VREF Routing
    10. 2.10 LPDDR4 VTT
    11. 2.11 CK, CMD_ADDR, and CTRL Topologies
    12. 2.12 Data Group Topologies
    13. 2.13 CK, CMD_ADDR, and CTRL Routing Specification
    14. 2.14 Data Group Routing Specification
    15. 2.15 Channel, Byte, and Bit Swapping
  6. 3LPDDR4 Board Design Simulations
    1. 3.1 Board Model Extraction
    2. 3.2 Board-Model Validation
    3. 3.3 S-Parameter Inspection
    4. 3.4 Time Domain Reflectometry (TDR) Analysis
    5. 3.5 Simulation Integrity Analysis
      1. 3.5.1 Simulation Setup
      2. 3.5.2 Simulation Parameters
      3. 3.5.3 Simulation Targets
        1. 3.5.3.1 Waveform Quality
        2. 3.5.3.2 Eye Quality
        3. 3.5.3.3 Delay Report
        4. 3.5.3.4 Mask Report
    6. 3.6 Design Example
      1. 3.6.1 Stack-Up
      2. 3.6.2 Routing
      3. 3.6.3 Model Verification
      4. 3.6.4 Simulation Results
  7. 4Revision History

2.6 LPDDR4 Keepout Region

The region of the PCB used for LPDDR4 circuitry must be isolated from other signals. The LPDDR4 keepout region is defined for this purpose and example is shown in Figure 2-5. The size of this region varies with the placement and DDR routing. Non-LPDDR4 signals should not be routed on the DDR signal layers within the LPDDR4 keepout region. Non-LPDDR4 signals may be routed in this region only if they are routed on other layers separated from the DDR signal layers by a ground layer. No breaks are allowed in the reference ground layers in this region. In addition, a solid VDDS_DDR power plane should exist across the entire keepout region.

J722S, AM67x, TDA4VEN-Q1, TDA4AEN-Q1 Example LPDDR4 Keepout Region for TDA4VM/DRA829 (Top View)Figure 2-5 Example LPDDR4 Keepout Region for TDA4VM/DRA829 (Top View)