AFE58JD16
- 16-Channel, AFE for Ultrasound Applications:
- Input Attenuator, LNA, LPF, ADC, and
CW Mixer - Digital Time Gain Compensation (DTGC)
- Total Gain Range: 6 dB to 45 dB
- Linear Input Range: 1 VPP
- Input Attenuator, LNA, LPF, ADC, and
- Input Attenuator with DTGC:
- 8-dB to 0-dB Attenuation with 0.125-dB Step
- Supports Matched Impedance for:
- 50-Ω to 800-Ω Source Impedance
- Low-Noise Amplifier (LNA) with DTGC:
- 14-dB to 45-dB Gain with 0.125-dB Step
- Low Input Current Noise: 1.2 pA/√Hz
- 3rd-Order, Linear-Phase, Low-Pass Filter (LPF):
- 10 MHz, 15 MHz, 20 MHz, and 25 MHz
- Analog-to-Digital Converter (ADC):
- 14-Bit ADC: 75-dBFS SNR at 65 MSPS
- 12-Bit ADC: 72-dBFS SNR at 80 MSPS
- LVDS Interface with a Maximum Speed Up to
1 GBPS - Optimized for Noise and Power:
- 90 mW/Ch at 1 nV/√Hz, 65 MSPS
- 55 mW/Ch at 1.45 nV/√Hz, 40 MSPS
- 59 mW/Ch in CW Mode
- Excellent Device-to-Device Gain Matching:
- ±0.5 dB (Typical)
- Low Harmonic Distortion: –60-dBc Level
- Fast and Consistent Overload Recovery
- Continuous Wave (CW) Path with:
- Low Close-In Phase Noise of –148 dBc/Hz
at 1-kHz frequency - Phase Resolution: λ / 16
- Supports 16X, 8X, 4X, and 1X CW Clocks
- Low Close-In Phase Noise of –148 dBc/Hz
- Digital Features:
- Digital I/Q Demodulator after ADC:
- Fractional Decimation Filter M = 1 to 63
with 0.25X Increment Step - Data Throughput Reduction After
Decimation - On-Chip RAM with 32 Preset Profiles
- Fractional Decimation Filter M = 1 to 63
- Digital I/Q Demodulator after ADC:
- 5-Gbps JESD Interface:
- JESD204B Subclass 0, 1, and 2
- 2, 4, or 8 Channels per JESD Lane
- Small Package: 15-mm × 15-mm NFBGA-289
The AFE58JD16 is a highly-integrated, analog front-end (AFE) solution specifically designed for ultrasound systems where high performance, low power, and small size are required.
To request a full datasheet or other design resources: request AFE58JD16
The AFE58JD16 is an integrated analog front-end (AFE) optimized for medical ultrasound application. The AFE58JD16 is a multichip module (MCM) device with two dies: VCA and ADC_CONV. Each die has total of 16 channels.
Each channel in the VCA die can be configured in two modes: time gain compensation (TGC) mode and continuous wave (CW) mode. In TGC mode, each channel includes an input attenuator (ATTEN), a low-noise amplifier (LNA) with variable-gain, and a third-order, low-pass filter (LPF). The attenuator supports an attenuation range of 8 dB to 0 dB, and the LNA supports gain ranges from 14 dB to 45 dB. The LPF cutoff frequency can be configured at 10 MHz, 15 MHz, 20 MHz, or 25 MHz to support ultrasound applications with different frequencies. In CW mode, each channel includes an LNA with a fixed gain of 18 dB, and a low-power passive mixer with 16 selectable phase delays. Different phase delays can be applied to each analog input signal to perform an on-chip beamforming operation. A harmonic filter in the CW mixer suppresses the third and fifth harmonic to enhance the sensitivity of the CW Doppler measurement. CW mode supports three clock modes: 16X, 8X, and 4X.
Each channel of the ADC_CONV die has a high-performance analog-to-digital converter (ADC) with a programmable resolution of 14 bits or 12 bits. The ADC achieves 75-dBFS signal-to-noise ratio (SNR) in 14-bit mode, and 72-dBFS SNR in 12-bit mode. This ADC provides excellent SNR at low-channel gain. The devices operate at maximum speeds of 65 MSPS and 80 MSPS, providing 14-bit and 12-bit output, respectively. The ADC is designed to scale power with sampling rate. The output interface of the ADC is a low-voltage differential signaling (LVDS) or JESD interface that can easily interface with low-cost field-programmable gate arrays (FPGAs).
The AFE58JD16 includes an optional digital demodulator and JESD204B data packing blocks after the 12- or 14- bit ADC. The digital in-phase and quadrature (I/Q) demodulator with programmable fractional decimation filters accelerates computationally-intensive algorithms at low power. The device also supports an optional JESD204B interface that runs up to 5 Gbps and further reduces the circuit-board routing challenges in high-channel count systems.
The AFE58JD16 also allows various power and noise combinations to be selected for optimizing system performance. Therefore, these devices are suitable ultrasound AFE solutions for systems with strict battery-life requirements. The AFE58JD16 is available in a 15-mm \xD7 15-mm NFBGA-289 package (ZAV package, S-PBGAN289) and is specified for operation from \x9640\xB0C to +85\xB0C. The device pinout is also similar to the AFE5818 family.
Request more information
Full data sheet and other design resources are available under NDA. Request now
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
AFE58JD16EVM — AFE58JD16 평가 모듈
AFE58JD16 평가 모듈(EVM)은 뛰어난 성능과 작은 크기가 필요한 초음파 시스템을 위해 특별히 설계된 고집적 아날로그 프론트 엔드(AFE) 솔루션입니다. AFE58JD16EVM은 완전한 타임 게인 제어(TGC) 영상 경로와 연속파 도플러(CWD) 경로를 통합하였습니다. 또한, 시스템 성능을 최적화하기 위해 다양한 전원/잡음 조합 중 하나를 선택할 수 있는 기능이 포함되어 있습니다. AFE58JD16EVM은 하이엔드 시스템뿐 아니라 휴대용 시스템에 적합한 초음파 AFE 솔루션입니다.
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| NFBGA (ZAV) | 289 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.