홈 전원 관리 LED 드라이버 LED 디스플레이 드라이버
홈
전원 관리
LED 드라이버
LED 디스플레이 드라이버

TLC5905

활성

데이터 출력 타이밍을 선택할 수 있는 8/16 채널 LED 드라이버

지금 주문
데이터 시트

TLC5905

활성
데이터 시트 지금 주문

제품 상세 정보

Features Error Flag, PWM LED Driver, Power good, Thermal shutdown Analog dimming steps 32 Data transfer rate (typ) (MHz) 15 Ch to ch accuracy (typ) (±%) 4 Rating Catalog Operating temperature range (°C) -20 to 85
Features Error Flag, PWM LED Driver, Power good, Thermal shutdown Analog dimming steps 32 Data transfer rate (typ) (MHz) 15 Ch to ch accuracy (typ) (±%) 4 Rating Catalog Operating temperature range (°C) -20 to 85
HTQFP (PAP) 64 144 mm² 12 x 12
  • Drive Capability and Output Counts:
    • 80 mA (Current Sink) × 16 Bits
    • 120 mA (Current Sink) × 8 Bits
  • Constant Current Output Range:
    • 5 mA to 80 mA/10 mA to 120 mA (Selectable by MODE Terminal) ( Current Value Setting for All Output Terminals Using External Resistor and Internal Brightness Control Register)
  • Constant Current Accuracy ±4% (Maximum Error Between Bits)
  • Voltage Applied to Constant Current Output Terminals:
    • Minimum 0.4 V (Output Current 5 mA to 40 mA)
    • Minimum 0.7 V (Output Current 40 mA to 80 mA)
  • 256 Gray Scale Display:
    • Pulse Width Control 256 Steps
  • Brightness Adjustment:
    • Output Current Adjustment for 32 Steps (Adjustment for Brightness Deviation Between LED Modules)
    • 8 Steps Brightness Control by 8 Times Speed Gray Scale Control Clock (Brightness Adjustment for Panel)
  • Error Output Signal Check:
    • Check Error Output Signal Line Such as Protection Circuit When Operating
  • Data Output Timing Selectable:
    • Select Data Output Timing for Shift Register Relative to Clock
  • OVM (Output Voltage Monitor):
    • Monitor Voltage on Constant Current Output Terminals (Detect LED Disconnection and Short Circuit)
  • WDT (Watchdog Timer):
    • Turn Output Off When Scan Signal Stopped
  • TSD (Thermal Shut Down):
    • Turn Output Off When Junction Temperature Exceeds Limit
  • Data Input:
    • Clock Synchronized 1 Bit Serial Input (Shmitt-Triggered Input)
  • Data Output:
    • Clock Synchronized 1 Bit Serial Output (3-State Output)
  • Input Signal Level:
    • CMOS Level
  • Power Supply Voltage...4.5 V to 5.5 V
  • Maximum Output Voltage...17 V
  • Data Transfer Rate...15 MHz (Max
  • Gray Scale Clock Frequency...8 MHz (Max)
  • Operating Free-Air Temperature Range
    -20°C to 85°C
  • 64-Pin HTQFP Package (PD = 4.9 W,
    TA = 25°C)
  • Drive Capability and Output Counts:
    • 80 mA (Current Sink) × 16 Bits
    • 120 mA (Current Sink) × 8 Bits
  • Constant Current Output Range:
    • 5 mA to 80 mA/10 mA to 120 mA (Selectable by MODE Terminal) ( Current Value Setting for All Output Terminals Using External Resistor and Internal Brightness Control Register)
  • Constant Current Accuracy ±4% (Maximum Error Between Bits)
  • Voltage Applied to Constant Current Output Terminals:
    • Minimum 0.4 V (Output Current 5 mA to 40 mA)
    • Minimum 0.7 V (Output Current 40 mA to 80 mA)
  • 256 Gray Scale Display:
    • Pulse Width Control 256 Steps
  • Brightness Adjustment:
    • Output Current Adjustment for 32 Steps (Adjustment for Brightness Deviation Between LED Modules)
    • 8 Steps Brightness Control by 8 Times Speed Gray Scale Control Clock (Brightness Adjustment for Panel)
  • Error Output Signal Check:
    • Check Error Output Signal Line Such as Protection Circuit When Operating
  • Data Output Timing Selectable:
    • Select Data Output Timing for Shift Register Relative to Clock
  • OVM (Output Voltage Monitor):
    • Monitor Voltage on Constant Current Output Terminals (Detect LED Disconnection and Short Circuit)
  • WDT (Watchdog Timer):
    • Turn Output Off When Scan Signal Stopped
  • TSD (Thermal Shut Down):
    • Turn Output Off When Junction Temperature Exceeds Limit
  • Data Input:
    • Clock Synchronized 1 Bit Serial Input (Shmitt-Triggered Input)
  • Data Output:
    • Clock Synchronized 1 Bit Serial Output (3-State Output)
  • Input Signal Level:
    • CMOS Level
  • Power Supply Voltage...4.5 V to 5.5 V
  • Maximum Output Voltage...17 V
  • Data Transfer Rate...15 MHz (Max
  • Gray Scale Clock Frequency...8 MHz (Max)
  • Operating Free-Air Temperature Range
    -20°C to 85°C
  • 64-Pin HTQFP Package (PD = 4.9 W,
    TA = 25°C)

The TLC5905 is a constant current driver that incorporates shift register, data latch, constant current circuitry with a current value adjustable and 256 gray scale display that uses pulse width control. The output current can be selected as maximum 80 mA with 16 bits or 120 mA with 8 bit. The current value of the constant current output is set by one external resistor. After this device is mounted on a printed-circuit board (PCB), the brightness deviation between LED modules (ICs) can be adjusted using an external data input, and the brightness control for the panel can be accomplished by the brightness adjustment circuitry. Also, the device incorporates the output voltage monitor (OVM) used for LED open detection (LOD) by monitoring constant current output. Moreover, the device incorporates watchdog timer (WDT) circuitry, which turns constant current output off when the scan signal stops during dynamic scanning operation, and thermal shutdown (TSD) circuitry, which turns constant current output off when the junction temperature exceeds the limit.

The TLC5905 is a constant current driver that incorporates shift register, data latch, constant current circuitry with a current value adjustable and 256 gray scale display that uses pulse width control. The output current can be selected as maximum 80 mA with 16 bits or 120 mA with 8 bit. The current value of the constant current output is set by one external resistor. After this device is mounted on a printed-circuit board (PCB), the brightness deviation between LED modules (ICs) can be adjusted using an external data input, and the brightness control for the panel can be accomplished by the brightness adjustment circuitry. Also, the device incorporates the output voltage monitor (OVM) used for LED open detection (LOD) by monitoring constant current output. Moreover, the device incorporates watchdog timer (WDT) circuitry, which turns constant current output off when the scan signal stops during dynamic scanning operation, and thermal shutdown (TSD) circuitry, which turns constant current output off when the junction temperature exceeds the limit.

filter 기타 LED 디스플레이 드라이버 찾기
다운로드 스크립트와 함께 비디오 보기 동영상

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
2개 모두 보기
유형 직함 날짜
* Data sheet LED Driver datasheet 1999/11/24
White paper Common LED Functions and LED Driver Design Considerations 2020/09/21

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

시뮬레이션 툴

PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®

TI용 PSpice®는 아날로그 회로의 기능을 평가하는 데 사용되는 설계 및 시뮬레이션 환경입니다. 완전한 기능을 갖춘 이 설계 및 시뮬레이션 제품군은 Cadence®의 아날로그 분석 엔진을 사용합니다. 무료로 제공되는 TI용 PSpice에는 아날로그 및 전력 포트폴리오뿐 아니라 아날로그 행동 모델에 이르기까지 업계에서 가장 방대한 모델 라이브러리 중 하나가 포함되어 있습니다.

TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
요청
패키지 핀 CAD 기호, 풋프린트 및 3D 모델
HTQFP (PAP) 64 Ultra Librarian
TI의 평가 항목에 대한 표준 약관이 적용됩니다.

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

포럼 주제 모두 보기(영문)

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상