TLK106

새 설계에 권장하지 않음

산업용 온도, 싱글 포트 10/100Mbps 이더넷 물리적 계층 트랜시버

지금 주문

데이터 시트

document-pdfAcrobat TLK105 TLK106 Industrial Temp, Single Port 10/100Mbs Ethernet Physical Layer Transceiver datasheet (Rev. C) (영어) PDF | HTML

TLK106

새 설계에 권장하지 않음

데이터 시트

지금 주문

제품 상세 정보

Datarate (Mbps)

10/100

Interface type

MII, RMII

Number of ports

Single

Rating

Catalog

Features

Cable diagnostics

Supply voltage (V)

3.3

Operating temperature range (°C)

0 to 0

Number of LEDs

1

ESD HBM (kV)

16

Datarate (Mbps)

10/100

Interface type

MII, RMII

Number of ports

Single

Rating

Catalog

Features

Cable diagnostics

Supply voltage (V)

3.3

Operating temperature range (°C)

0 to 0

Number of LEDs

1

ESD HBM (kV)

16

VQFN (RHB)

32

25 mm² 5 x 5

Low Power Consumption:
- Single Supply: <205mW PHY, 275mW with
  Center Tap (Typical)
- Dual Supplies: <126mW PHY, 200mW with
  Center Tap (Typical)
Programmable Power Back Off to reduce PHY
power up to 20% in systems with shorter cables
Low deterministic latency supports IEEE1588
implementation
Cable Diagnostics (TLK106)
Programmable Fast Link Down Modes, <10µs
reaction time
Variable I/O voltage range: 3.3V, 2.5V, 1.8V
MAC Interface I/O voltage range:
- MII I/O voltage range: 3.3V, 2.5V, 1.8V
- RMII I/O voltage range: 3.3V, 2.5V
Fixed TX Clock to XI, with programmable phase
shift
Auto-MDIX for 10/100Mbs
Energy Detection Mode
MII and RMII Capabilities
Serial Management Interface
IEEE 802.3u MII
IEEE 802.3u Auto-Negotiation and Parallel
Detection
Error-Free 100Base-T Operation up to 150 Meters
Under Typical Conditions
Error-Free 10Base-T Operation up to 300 Meters
Under Typical Conditions
IEEE 802.3u ENDEC, 10Base-T
Transceivers and Filters
IEEE 802.3u PCS, 100Base-TX Transceivers
Integrated ANSI X3.263 Compliant TP-PMD
Physical Sublayer with Adaptive Equalization and
Baseline Wander Compensation
Programmable LED Support Link, Activity
10/100Mbs Packet BIST (Built in Self Test)
HBM ESD protection on RD± and TD± of 16kV
32-pin QFN (5mm) × (5mm)

Low Power Consumption:
- Single Supply: <205mW PHY, 275mW with
  Center Tap (Typical)
- Dual Supplies: <126mW PHY, 200mW with
  Center Tap (Typical)
Programmable Power Back Off to reduce PHY
power up to 20% in systems with shorter cables
Low deterministic latency supports IEEE1588
implementation
Cable Diagnostics (TLK106)
Programmable Fast Link Down Modes, <10µs
reaction time
Variable I/O voltage range: 3.3V, 2.5V, 1.8V
MAC Interface I/O voltage range:
- MII I/O voltage range: 3.3V, 2.5V, 1.8V
- RMII I/O voltage range: 3.3V, 2.5V
Fixed TX Clock to XI, with programmable phase
shift
Auto-MDIX for 10/100Mbs
Energy Detection Mode
MII and RMII Capabilities
Serial Management Interface
IEEE 802.3u MII
IEEE 802.3u Auto-Negotiation and Parallel
Detection
Error-Free 100Base-T Operation up to 150 Meters
Under Typical Conditions
Error-Free 10Base-T Operation up to 300 Meters
Under Typical Conditions
IEEE 802.3u ENDEC, 10Base-T
Transceivers and Filters
IEEE 802.3u PCS, 100Base-TX Transceivers
Integrated ANSI X3.263 Compliant TP-PMD
Physical Sublayer with Adaptive Equalization and
Baseline Wander Compensation
Programmable LED Support Link, Activity
10/100Mbs Packet BIST (Built in Self Test)
HBM ESD protection on RD± and TD± of 16kV
32-pin QFN (5mm) × (5mm)

The TLK10x is a single-port Ethernet PHY for 10Base-T and 100Base TX signaling. This device integrates all the physical-layer functions needed to transmit and receive data on standard twisted-pair cables. The TLK10x supports the standard Media Independent Interface (MII) and Reduced Media Independent Interface (RMII) for direct connection to a Media Access Controller (MAC).

The TLK10x is designed for power-supply flexibility, and can operate with a single 3.3V power supply or with combinations of 3.3V and 1.55V power supplies for reduced power operation.

The TLK10x uses mixed-signal processing to perform equalization, data recovery, and error correction to achieve robust operation over CAT 5 twisted-pair wiring. This device not only meets the requirements of IEEE 802.3, but maintains high margins in terms of cross-talk and alien noise.

The TLK10x Ethernet PHY has a special Power Back Off mode to conserve power in systems with relatively short cables. This mode provides the flexibility to reduce system power when the system is not required to drive the standard IEEE 802.3 100m cable length, or the extended 150m, error-free cable reach of the TLK10x. For more detail, see application note SLLA328.

The TLK10x is a single-port Ethernet PHY for 10Base-T and 100Base TX signaling. This device integrates all the physical-layer functions needed to transmit and receive data on standard twisted-pair cables. The TLK10x supports the standard Media Independent Interface (MII) and Reduced Media Independent Interface (RMII) for direct connection to a Media Access Controller (MAC).

The TLK10x is designed for power-supply flexibility, and can operate with a single 3.3V power supply or with combinations of 3.3V and 1.55V power supplies for reduced power operation.

The TLK10x uses mixed-signal processing to perform equalization, data recovery, and error correction to achieve robust operation over CAT 5 twisted-pair wiring. This device not only meets the requirements of IEEE 802.3, but maintains high margins in terms of cross-talk and alien noise.

The TLK10x Ethernet PHY has a special Power Back Off mode to conserve power in systems with relatively short cables. This mode provides the flexibility to reduce system power when the system is not required to drive the standard IEEE 802.3 100m cable length, or the extended 150m, error-free cable reach of the TLK10x. For more detail, see application note SLLA328.

filter

기타 이더넷 PHY 찾기

다운로드

기술 자료

star

=TI에서 선정한 이 제품의 인기 문서

검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.

1개 모두 보기

	유형	직함		날짜
*	Data sheet	TLK105 TLK106 Industrial Temp, Single Port 10/100Mbs Ethernet Physical Layer Transceiver datasheet (Rev. C)	PDF \| HTML	2016/04/22

TLK106

산업용 온도, 싱글 포트 10/100Mbps 이더넷 물리적 계층 트랜시버

TLK106

제품 상세 정보

기술 자료

주문 및 품질