TPS61310
- Operational Modes:
- Video Light and Flash Strobe
- Voltage Regulated Converter: 3.8 V to 5.7 V With Down Mode
- Standby: 2 µA (Typical)
- LED VF Measurement
- Power-Save Mode for Improved Efficiency at Low Output Power, Up to 95% Efficiency
- I2C Compatible Interface up to 3.4 Mbps
- Dual Wire Camera Module Interface
- Zero Latency Tx-Masking Input
- Hardware Reset Input
- Privacy Indicator LED Output
- GPIO and Power Good Output
- Various Safe Operation and Robust Handling Features:
- LED Temperature Monitoring
- Open and Shorted LED Detection and Protection
- Integrated LED Safety Timer
- Automatic Battery Voltage Droop Monitoring and Protection
- Smooth LED Current Ramp-Up and Ramp-Down
- Undervoltage Lockout
- Total Solution Size of Less Than 25 mm2
- Available in a 20-Pin NanoFree™ DSBGA Package
The TPS6131x family is an integrated solution with a wide feature set for driving up to three LEDs for still-camera flash strobe and video-camera lighting applications. It is based on a high efficiency synchronous boost topology with combinable current sinks to drive up to three white LEDs in parallel. The 2-MHz switching frequency allows the use of small and low-profile 2.2-µH inductors. To optimize overall efficiency, the device operates with a low LED-feedback voltage and regulated output-voltage adaptation.
The device integrates a control scheme that automatically optimizes the LED current flash budget as a function of the battery voltage condition.
The TPS6131x not only operates as a regulated current source, but also as a standard voltage boost regulator. The device enters power-save mode operation at light load currents to maintain high efficiency over the entire load current range. These operating modes can be useful to supply other high power devices in the system (for example, a hands-free audio PA).
To simplify video light and flash synchronization with the camera module, the device offers a dedicated control interface (STRB0, STRB1) for zero latency LED turnon time.
기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | TPS6131x 1.5-A Multiple LED Camera Flash and Video Light Driver With I2C Compatible Interface datasheet (Rev. D) | PDF | HTML | 2016/09/07 |
| White paper | Common LED Functions and LED Driver Design Considerations | 2020/09/21 | ||
| Application note | Performing Accurate PFM Mode Efficiency Measurements (Rev. A) | 2018/12/11 | ||
| Selection guide | Power Management Guide 2018 (Rev. R) | 2018/06/25 | ||
| Application note | Choosing an Appropriate Pull-up/Pull-down Resistor for Open Drain Outputs | 2011/09/19 | ||
| EVM User's guide | TPS61310 EVM user's guide | 2010/10/26 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPS61310EVM-638 — I2C 호환 인터페이스를 지원하는 TPS61310_1.5A 여러 LED 카메라 플래시 드라이버용 평가 모듈
The TPS61310EVM-638 Evaluation Module (EVM) demonstrates the Texas Instruments TPS61310 LED camera flash and video light driver with I2C interface. The user’s guide describes the characteristics, functions, and use of the TPS61310EVM-638 Evaluation Module This document includes setup (...)
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| DSBGA (YFF) | 20 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치