인터페이스 USB IC USB Type-C 및 USB 전원 공급 IC

TPS65988

활성

일체형 전원 스위치가 있는 듀얼 포트 USB-C® 및 PD(Power Delivery) 컨트롤러

제품 상세 정보

Function Type-C Type PD controller Power role DRP, Sink, Source Alternate mode Yes External power-path control GPIO, I2C Data role DFP, DRD, UFP Internal power path 20 V 5 A Rating Catalog Dead battery support Yes Operating temperature range (°C) -10 to 75
Function Type-C Type PD controller Power role DRP, Sink, Source Alternate mode Yes External power-path control GPIO, I2C Data role DFP, DRD, UFP Internal power path 20 V 5 A Rating Catalog Dead battery support Yes Operating temperature range (°C) -10 to 75
VQFN (RSH) 56 49 mm² 7 x 7
  • This device is certified by the USB-IF for PD3.0
    • PD3.0 silicon is required for certification of new USB PD designs
      • TID#: 1099
    • Article on PD2.0 vs. PD3.0
  • TPS65988 is a fully configurable dual port USB PD device controller
    • Ability to source and sink up to 20 V/5 A
    • Alternate mode support
      • DisplayPort
    • Control for external DC/DC supplies, high speed data muxes, and other peripheral devices through either GPIO or I2C
    • GUI tool to easily configure TPS65988 for various applications TPS65988X-CONFIG
    • Power management
      • Power supply from 3.3 V or VBUS source
      • 3.3-V LDO output for dead battery support
    • For a more extensive selection guide and getting started information, please refer to www.ti.com/usb-c and E2E guide
  • Integrated fully managed power paths:
    • Integrated two 5-20 V, 5-A, 25-mΩ bidirectional switches
    • UL2367 cert #: 20190107-E169910
    • IEC62368-1 cert #: US-34617-UL
  • Integrated robust power path protection
    • Integrated reverse current protection, undervoltage protection, overvoltage protection, and slew rate control for both 20-V/5-A power paths when configured to Sink
    • Integrated undervoltage protection, overvoltage protection, and current limiting for inrush current protection for both 20-V/5-A power paths when configured to Source
  • USB Type-C power delivery (PD) controller
    • 13 configurable GPIOs
    • BC1.2 charging support
    • USB PD 3.0 certified
    • USB Type-C specification certified
    • Cable attach and orientation detection
    • Integrated VCONN switch
    • Physical layer and policy engine
    • 3.3-V LDO output for dead battery support
    • Power supply from 3.3 V or VBUS source
    • 1 I2C primary or secondary port
    • 1 I2C primary only port
    • 1 I2C secondary only port
  • This device is certified by the USB-IF for PD3.0
    • PD3.0 silicon is required for certification of new USB PD designs
      • TID#: 1099
    • Article on PD2.0 vs. PD3.0
  • TPS65988 is a fully configurable dual port USB PD device controller
    • Ability to source and sink up to 20 V/5 A
    • Alternate mode support
      • DisplayPort
    • Control for external DC/DC supplies, high speed data muxes, and other peripheral devices through either GPIO or I2C
    • GUI tool to easily configure TPS65988 for various applications TPS65988X-CONFIG
    • Power management
      • Power supply from 3.3 V or VBUS source
      • 3.3-V LDO output for dead battery support
    • For a more extensive selection guide and getting started information, please refer to www.ti.com/usb-c and E2E guide
  • Integrated fully managed power paths:
    • Integrated two 5-20 V, 5-A, 25-mΩ bidirectional switches
    • UL2367 cert #: 20190107-E169910
    • IEC62368-1 cert #: US-34617-UL
  • Integrated robust power path protection
    • Integrated reverse current protection, undervoltage protection, overvoltage protection, and slew rate control for both 20-V/5-A power paths when configured to Sink
    • Integrated undervoltage protection, overvoltage protection, and current limiting for inrush current protection for both 20-V/5-A power paths when configured to Source
  • USB Type-C power delivery (PD) controller
    • 13 configurable GPIOs
    • BC1.2 charging support
    • USB PD 3.0 certified
    • USB Type-C specification certified
    • Cable attach and orientation detection
    • Integrated VCONN switch
    • Physical layer and policy engine
    • 3.3-V LDO output for dead battery support
    • Power supply from 3.3 V or VBUS source
    • 1 I2C primary or secondary port
    • 1 I2C primary only port
    • 1 I2C secondary only port

The TPS65988 is a highly integrated stand-alone Dual Port USB Type-C and Power Delivery (PD) controller providing cable plug and orientation detection for a single USB Type-C connector. Upon cable detection, the TPS65988 communicates on the CC wire using the USB PD protocol. When cable detection and USB PD negotiation are complete, the TPS65988 enables the appropriate power path and configures alternate mode settings for external multiplexers. The TPS65988 integrates fully managed power paths with robust protection for a complete USB-C PD solution. The TPS65988 also enables the appropriate power path and configures alternate mode settings for external multiplexers.

The TPS65988 is a highly integrated stand-alone Dual Port USB Type-C and Power Delivery (PD) controller providing cable plug and orientation detection for a single USB Type-C connector. Upon cable detection, the TPS65988 communicates on the CC wire using the USB PD protocol. When cable detection and USB PD negotiation are complete, the TPS65988 enables the appropriate power path and configures alternate mode settings for external multiplexers. The TPS65988 integrates fully managed power paths with robust protection for a complete USB-C PD solution. The TPS65988 also enables the appropriate power path and configures alternate mode settings for external multiplexers.

다운로드 스크립트와 함께 비디오 보기 동영상

관심 가지실만한 유사 제품

open-in-new 대안 비교
비교 대상 장치와 유사한 기능
신규 TPS25751 활성 습도 감지 및 프로그래머블 전원 공급 장치를 지원하는 USB-C® PD(Power Delivery) 3.1 컨트롤러 For applications requiring USB-C Power Delivery and no support for alternate modes

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
19개 모두 보기
유형 직함 날짜
* Data sheet TPS65988 Dual Port USB Type-C® and USB PD Controller with Integrated Source and Sink Power Path Supporting USB3 and Alternate Mode datasheet (Rev. B) PDF | HTML 2021/08/05
White paper A Primer on USB Type-C and Power Delivery Applications and Requirements (Rev. B) PDF | HTML 2022/03/25
Application note TPS65988DH: Integrated Type-C PD Dual-Port Wall Socket With Power Balancing (Rev. A) PDF | HTML 2022/01/06
Application note TPS6598x USB PD Power Negotiation and Multiport Source/Sink Behavior Application PDF | HTML 2021/04/30
Application note TPS65987D GPIO Events (Rev. A) PDF | HTML 2021/01/26
Application note Hardware Design Guideline for TPS65987 and TPS65988 USB Power Delivery (Rev. C) PDF | HTML 2021/01/08
User guide TPS6598x Application Customization Tool (Rev. C) 2020/09/14
Application note TPS65988 BC1.2 Implementation Guideline (Rev. A) 2020/01/16
Application note USB Power Delivery - Compliance Tests (Rev. A) 2019/09/25
Application note TPS65987/8 Power and Data Role Swaps 2019/06/10
Application note TPS6598x Dead Battery Application Note 2018/12/20
Application note TPS65987 and TPS65988 SPI Flash Firmware Update Over I2C (Rev. A) 2018/10/17
Application note TPS65987D and TPS65988 User Alternate Modes (Rev. A) 2018/09/14
User guide TPS65987DDH and TPS65988DH Host Interface Technical Reference Manual (Rev. B) 2018/09/14
White paper Fast role swap power architecture white paper 2018/08/20
Application note PD Alternate Mode: DisplayPort (Rev. B) 2018/07/31
Application note TPS65988 and TPS65987D PD3.0 Fast Role Swap 2018/07/30
Application note Using I2C Master in TPS65987D and TPS65988 PD Controllers 2018/07/25
Application note TPS65987D, TPS65988 Power Path Performance and Protection 2018/05/30

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

IDE, 구성, 컴파일러 또는 디버거

TPS6598X-CONFIG TPS65982 Configuration Tool

What you need to get started:

Step 1: Watch the TPS6598X GUI tool videos
Step 2: Download the TPS6598X GUI
Step 3: Order the USB-C-PD-DUO-EVM and read the user's guide
Step 4: Watch the EVM Tutorial


The TPS6598x configuration tool assists in the design phase by providing a GUI interface to configure (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

제품
USB Type-C 및 USB 전원 공급 IC
TPS65981 USB Type-C® 및 USB-C® PD(Power Delivery) 컨트롤러, 전원 스위치 및 고속 멀티플렉서 TPS65982 USB Type-C™ 및 USB PD 컨트롤러 전원 스위치 및 고속 멀티플렉서 TPS65987D 전원 스위치가 통합된 USB Type-C® 및 USB-C® PD(Power Delivery) 컨트롤러 TPS65988 일체형 전원 스위치가 있는 듀얼 포트 USB-C® 및 PD(Power Delivery) 컨트롤러
하드웨어 개발
평가 보드
TPS65981EVM TPS65981 USB Type-C® 및 USB PD(Power Delivery) 컨트롤러, 전원 스위치, 고속 멀티플렉서 EVM TPS65982-EVM TPS65982 USB Type-C® 및 USB PD() 컨트롤러 전원 스위치 및 고속 멀티플렉서 EVM USB-C-PD-DUO-EVM Power DUO source and sink evaluation module
소프트웨어
IDE, 구성, 컴파일러 또는 디버거
TPS6598X-CONFIG TPS6598x 구성 툴
시뮬레이션 모델

TPS65988 IBIS Model

SLVMC47.ZIP (29 KB) - IBIS Model
시뮬레이션 툴

PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®

TI용 PSpice®는 아날로그 회로의 기능을 평가하는 데 사용되는 설계 및 시뮬레이션 환경입니다. 완전한 기능을 갖춘 이 설계 및 시뮬레이션 제품군은 Cadence®의 아날로그 분석 엔진을 사용합니다. 무료로 제공되는 TI용 PSpice에는 아날로그 및 전력 포트폴리오뿐 아니라 아날로그 행동 모델에 이르기까지 업계에서 가장 방대한 모델 라이브러리 중 하나가 포함되어 있습니다.

TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
시뮬레이션 툴

TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
사용 설명서: PDF
패키지 CAD 기호, 풋프린트 및 3D 모델
VQFN (RSH) 56 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상