JAJSMN8D December   2000  – August 2021 DCR021205 , DCR022405

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Isolation
        1. 7.3.1.1 Operation or Functional Isolation
        2. 7.3.1.2 Basic or Enhanced Isolation
        3. 7.3.1.3 Working Voltage
        4. 7.3.1.4 Isolation Voltage Rating
        5. 7.3.1.5 Repeated High-Voltage Isolation Testing
      2. 7.3.2 Power Stage
      3. 7.3.3 Oscillator and Watchdog
      4. 7.3.4 ERROR Flag
      5. 7.3.5 Synchronization
      6. 7.3.6 Construction
      7. 7.3.7 Decoupling – Ripple Reduction
    4. 7.4 Device Functional Modes
      1. 7.4.1 Device Disable and Enable
      2. 7.4.2 Regulated Output Disable and Enable
  8. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 DCR02 Single Voltage Output
      2. 8.1.2 Generating Two Positive Output Voltages
      3. 8.1.3 Generation of Dual Polarity Voltages from Two Self-Synchronized DCR02s
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Input Capacitor
        2. 8.2.2.2 Output Capacitor
        3. 8.2.2.3 Filter Capacitor
        4. 8.2.2.4 ERROR Flag
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Examples
    3. 10.3 Thermal Consideration
  11. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.1.1 DCR02 Single Voltage Output

The DCR02 can be used to provide a single voltage output by connecting the circuit as shown in Figure 8-1. The ERROR output signal is pulled up to the value of VOUT for the particular DCR02 being used. The value of RERR depends on the loading on the ERROR line; however, the total load on the ERROR line must not exceed the value given in the Section 6.5.

The output can be permanently enabled by connecting the ENABLE pin to the VREC pin. The DCR02 can be enabled remotely by connecting the ENABLE pin to VREC through a pull-up resistor (REN); the value of this resistor is not critical for the DCR02, because only a small current flows. Switch SW1 can be used to pull the ENABLE pin low, thus disabling the output. The switching devices can be a bipolar transistor, FET, or a mechanical device; the main load that it senses is REN.

GUID-8CFC07A9-1D27-489D-8C35-B347CBC2F181-low.gif
Low-ESR, ceramic capacitors are required for CIN, COUT, and CFILTER.
Figure 8-1 DCR02 Single Output Voltage