Inicio Gestión de la energía Controladores LED Drivers para pantallas LED
Inicio
Gestión de la energía
Controladores LED
Drivers para pantallas LED

TLC5905

ACTIVO

Controlador LED de 8/16 canales con temporización de salida de datos seleccionable

Haga su pedido ahora
Hoja de datos

TLC5905

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Features Error Flag, PWM LED Driver, Power good, Thermal shutdown Analog dimming steps 32 Data transfer rate (typ) (MHz) 15 Ch to ch accuracy (typ) (±%) 4 Rating Catalog Operating temperature range (°C) -20 to 85
Features Error Flag, PWM LED Driver, Power good, Thermal shutdown Analog dimming steps 32 Data transfer rate (typ) (MHz) 15 Ch to ch accuracy (typ) (±%) 4 Rating Catalog Operating temperature range (°C) -20 to 85
HTQFP (PAP) 64 144 mm² 12 x 12
  • Drive Capability and Output Counts:
    • 80 mA (Current Sink) × 16 Bits
    • 120 mA (Current Sink) × 8 Bits
  • Constant Current Output Range:
    • 5 mA to 80 mA/10 mA to 120 mA (Selectable by MODE Terminal) ( Current Value Setting for All Output Terminals Using External Resistor and Internal Brightness Control Register)
  • Constant Current Accuracy ±4% (Maximum Error Between Bits)
  • Voltage Applied to Constant Current Output Terminals:
    • Minimum 0.4 V (Output Current 5 mA to 40 mA)
    • Minimum 0.7 V (Output Current 40 mA to 80 mA)
  • 256 Gray Scale Display:
    • Pulse Width Control 256 Steps
  • Brightness Adjustment:
    • Output Current Adjustment for 32 Steps (Adjustment for Brightness Deviation Between LED Modules)
    • 8 Steps Brightness Control by 8 Times Speed Gray Scale Control Clock (Brightness Adjustment for Panel)
  • Error Output Signal Check:
    • Check Error Output Signal Line Such as Protection Circuit When Operating
  • Data Output Timing Selectable:
    • Select Data Output Timing for Shift Register Relative to Clock
  • OVM (Output Voltage Monitor):
    • Monitor Voltage on Constant Current Output Terminals (Detect LED Disconnection and Short Circuit)
  • WDT (Watchdog Timer):
    • Turn Output Off When Scan Signal Stopped
  • TSD (Thermal Shut Down):
    • Turn Output Off When Junction Temperature Exceeds Limit
  • Data Input:
    • Clock Synchronized 1 Bit Serial Input (Shmitt-Triggered Input)
  • Data Output:
    • Clock Synchronized 1 Bit Serial Output (3-State Output)
  • Input Signal Level:
    • CMOS Level
  • Power Supply Voltage...4.5 V to 5.5 V
  • Maximum Output Voltage...17 V
  • Data Transfer Rate...15 MHz (Max
  • Gray Scale Clock Frequency...8 MHz (Max)
  • Operating Free-Air Temperature Range
    -20°C to 85°C
  • 64-Pin HTQFP Package (PD = 4.9 W,
    TA = 25°C)
  • Drive Capability and Output Counts:
    • 80 mA (Current Sink) × 16 Bits
    • 120 mA (Current Sink) × 8 Bits
  • Constant Current Output Range:
    • 5 mA to 80 mA/10 mA to 120 mA (Selectable by MODE Terminal) ( Current Value Setting for All Output Terminals Using External Resistor and Internal Brightness Control Register)
  • Constant Current Accuracy ±4% (Maximum Error Between Bits)
  • Voltage Applied to Constant Current Output Terminals:
    • Minimum 0.4 V (Output Current 5 mA to 40 mA)
    • Minimum 0.7 V (Output Current 40 mA to 80 mA)
  • 256 Gray Scale Display:
    • Pulse Width Control 256 Steps
  • Brightness Adjustment:
    • Output Current Adjustment for 32 Steps (Adjustment for Brightness Deviation Between LED Modules)
    • 8 Steps Brightness Control by 8 Times Speed Gray Scale Control Clock (Brightness Adjustment for Panel)
  • Error Output Signal Check:
    • Check Error Output Signal Line Such as Protection Circuit When Operating
  • Data Output Timing Selectable:
    • Select Data Output Timing for Shift Register Relative to Clock
  • OVM (Output Voltage Monitor):
    • Monitor Voltage on Constant Current Output Terminals (Detect LED Disconnection and Short Circuit)
  • WDT (Watchdog Timer):
    • Turn Output Off When Scan Signal Stopped
  • TSD (Thermal Shut Down):
    • Turn Output Off When Junction Temperature Exceeds Limit
  • Data Input:
    • Clock Synchronized 1 Bit Serial Input (Shmitt-Triggered Input)
  • Data Output:
    • Clock Synchronized 1 Bit Serial Output (3-State Output)
  • Input Signal Level:
    • CMOS Level
  • Power Supply Voltage...4.5 V to 5.5 V
  • Maximum Output Voltage...17 V
  • Data Transfer Rate...15 MHz (Max
  • Gray Scale Clock Frequency...8 MHz (Max)
  • Operating Free-Air Temperature Range
    -20°C to 85°C
  • 64-Pin HTQFP Package (PD = 4.9 W,
    TA = 25°C)

The TLC5905 is a constant current driver that incorporates shift register, data latch, constant current circuitry with a current value adjustable and 256 gray scale display that uses pulse width control. The output current can be selected as maximum 80 mA with 16 bits or 120 mA with 8 bit. The current value of the constant current output is set by one external resistor. After this device is mounted on a printed-circuit board (PCB), the brightness deviation between LED modules (ICs) can be adjusted using an external data input, and the brightness control for the panel can be accomplished by the brightness adjustment circuitry. Also, the device incorporates the output voltage monitor (OVM) used for LED open detection (LOD) by monitoring constant current output. Moreover, the device incorporates watchdog timer (WDT) circuitry, which turns constant current output off when the scan signal stops during dynamic scanning operation, and thermal shutdown (TSD) circuitry, which turns constant current output off when the junction temperature exceeds the limit.

The TLC5905 is a constant current driver that incorporates shift register, data latch, constant current circuitry with a current value adjustable and 256 gray scale display that uses pulse width control. The output current can be selected as maximum 80 mA with 16 bits or 120 mA with 8 bit. The current value of the constant current output is set by one external resistor. After this device is mounted on a printed-circuit board (PCB), the brightness deviation between LED modules (ICs) can be adjusted using an external data input, and the brightness control for the panel can be accomplished by the brightness adjustment circuitry. Also, the device incorporates the output voltage monitor (OVM) used for LED open detection (LOD) by monitoring constant current output. Moreover, the device incorporates watchdog timer (WDT) circuitry, which turns constant current output off when the scan signal stops during dynamic scanning operation, and thermal shutdown (TSD) circuitry, which turns constant current output off when the junction temperature exceeds the limit.

filter Buscar otro/a Drivers para pantallas LED
Descargar Ver vídeo con transcripción Video

Documentación técnica

star =Principal documentación para este producto seleccionada por TI
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 2
Tipo Título Fecha
* Data sheet LED Driver datasheet 24 nov 1999
White paper Common LED Functions and LED Driver Design Considerations 21 sep 2020

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Herramienta de simulación

PSPICE-FOR-TI — PSpice® para herramienta de diseño y simulación de TI

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Solicitar
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
HTQFP (PAP) 64 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Información incluida:
  • RoHS
  • REACH
  • Marcado del dispositivo
  • Acabado de plomo/material de la bola
  • Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
  • Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
  • Contenido del material
  • Resumen de calificaciones
  • Monitoreo continuo de confiabilidad
Información incluida:
  • Lugar de fabricación
  • Lugar de ensamblaje

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI. ​​​​​​​​​​​​​​

Videos