DRV8302
- 8-V to 60-V Operating Supply Voltage Range
- 1.7-A Source and 2.3-A Sink Gate Drive Current Capability
- Bootstrap Gate Driver With 100% Duty Cycle Support
- 6 or 3 PWM Input Modes
- Dual Integrated Current Shunt Amplifiers With Adjustable Gain and Offset
- 3.3-V and 5-V Interface Support
- Hardware Control Interface
- Protection Features:
- Programmable Dead Time Control (DTC)
- Programmable Overcurrent Protection (OCP)
- PVDD and GVDD Undervoltage Lockout (UVLO)
- GVDD Overvoltage Lockout (OVLO)
- Overtemperature Warning/Shutdown (OTW/OTS)
- Reported through nFAULT and nOCTW pins
All trademarks are the property of their respective owners.
The DRV8302 is a gate driver IC for three phase motor drive applications. It provides three half bridge drivers, each capable of driving two N-channel MOSFETs. The device supports up to 1.7-A source and 2.3-A peak current capability. The DRV8302 can operate off of a single power supply with a wide range from 8-V to 60-V. It uses a bootstrap gate driver architecture with trickle charge circuitry to support 100% duty cycle. The DRV8302 uses automatic hand shaking when the high side or low side MOSFET is switching to prevent current shoot through. Integrated VDS sensing of the high and low side MOSFETs is used to protect the external power stage against overcurrent conditions.
The DRV8303 includes two current shunt amplifiers for accurate current measurement. The amplifiers support bi-directional current sensing and provide and adjustable output offset up to 3 V.
The DRV8302 also includes an integrated switching mode buck converter with adjustable output and switching frequency. The buck converter can provide up to 1.5 A to support MCU or additional system power needs.
A hardware interface allows for configuring various device parameters including dead time, overcurrent, PWM mode, and amplifier settings. Error conditions are reported through the nFAULT and nOCTW pins.
For all available packages, see the orderable addendum at the end of the data sheet.기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | DRV8302 Three Phase Gate Driver With Dual Current Shunt Amplifiers and Buck Regulator – Hardware Controlled datasheet (Rev. C) | PDF | HTML | 2016/03/07 |
| Application note | Best Practices for Board Layout of Motor Drivers (Rev. B) | PDF | HTML | 2021/10/14 | |
| Application note | Hardware Design Considerations for an Electric Bicycle using BLDC Motor (Rev. B) | 2021/06/23 | ||
| Application note | System Design Considerations for High-Power Motor Driver Applications | PDF | HTML | 2021/06/22 | |
| White paper | Power Electronics in Motor Drives: Where is it? (Rev. A) | 2019/10/01 | ||
| Application note | Hardware Design Considerations for an Efficient Vacuum Cleaner Using a BLDC Moto (Rev. B) | PDF | HTML | 2019/03/06 | |
| Application note | InstaSPIN(tm) BLDC Lab | 2011/11/15 | ||
| Application note | Sensored 3-Phase BLDC Motor Control Using MSP430 | 2011/07/20 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
BOOSTXL-DRV8301 — DRV8301 및 NexFET™ MOSFET을 지원하는 모터 드라이브 부스터팩
The BOOSTXL-DRV8301 is 10A, 3-phase brushless DC drive stage based on the DRV8301 pre-driver and CSD18533Q5A NexFET™ power MOSFET. The module has 3x low side current sense amps (2 internal to DRV8301, 1 external). The module also has a 1.5A step down buck converter, is fully protected with (...)
INSTASPIN-BLDC — InstaSPIN™-BLDC 솔루션
TIDM-THREEPHASE-BLDC-HC — 3상 브러시리스/PMSM(영구자석 동기 모터) 고전류 모터 제어 솔루션
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| HTSSOP (DCA) | 56 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치